A Two-Stage Method for Structural Damage Prognosis in Shear Frames Based on Story Displacement Index and Modal Residual Force

Rasouli, Asghar; Kourehli, Seyed Sina; Ghodrati Amiri, Gholamreza; Kheyroddin, Ali

doi:https://doi.org/10.1155/2015/527537

Advances in Civil Engineering

On this page

Abstract Introduction Conclusions References Copyright Related Articles

Research Article | Open Access

Volume 2015 | Article ID 527537 | https://doi.org/10.1155/2015/527537

A Two-Stage Method for Structural Damage Prognosis in Shear Frames Based on Story Displacement Index and Modal Residual Force

Asghar Rasouli,¹Seyed Sina Kourehli,^2,3Gholamreza Ghodrati Amiri,⁴and Ali Kheyroddin⁵

Academic Editor: Amir Hossein Gandomi

Received25 Sept 2014

Accepted05 Mar 2015

Published13 May 2015

Abstract

A two-stage method is proposed to properly identify the location and the extent of damage in shear frames. In the first stage, a story displacement index (SDI) is presented to precisely locate the damage in the shear frame which is calculated using the modal analysis information of the damaged structure. In the second stage, by defining a new objective function, the extent of the actual damage is determined via an imperialist competitive algorithm. The performance of the proposed method is demonstrated by implementing the technique to three examples containing five-, ten-, and twenty-five-story shear frames with noises and without them in modal data. Moreover, the performance of the proposed method has been verified through using a benchmark problem. Numerical results show the high efficiency of the proposed method for accurately identifying the location and the extent of structural damage in shear frames.

1. Introduction

Damage detection is one of the branches of structural health monitoring (SHM) which has recently attracted many scientific efforts. Health monitoring refers to a process of measuring and interpreting data from a system of sensors distributed about a structural system to objectively quantify the condition of the structure (Johnson et al. [1] and Zingoni [2]). Damage detection techniques have been successfully applied to several real-world problems. Based on the performance of structures, damage detection methods can be categorized into four levels [3]. The first level is devoted to detection of existing damage in a structure, and the second and third levels focus on the determination of the location and severity of damage in structures, respectively. The last level is a complete study that includes the estimation of the residual life of a structure, reaching a point that requires more information from fracture mechanics and structural reliability.

The fundamental idea for the vibration-based damage identification is that the damage-induced changes in the physical properties (e.g., mass, damping, and stiffness) will cause detectable changes in modal properties (e.g., natural frequencies, modal damping, and mode shapes). For instance, reductions in stiffness result from the onset of the cracks. Therefore, it is intuitive that damage can be identified by analyzing the changes in vibration features of the structure. In the rich literature of damage detection methods, the most important are the damage assessment methods based on observations of structural vibrations (Doebling et al. [4], Sohn et al. [5], and Salawu [6]). Most of these methods are based on detection of characteristic patterns of changes in the natural frequencies of the structure (Hassiotis and Jeong [7], Capecchi and Vestroni [8], and Xia and Hao [9]) or on observations of differences in the shapes of their natural modes (Maeck and De Roeck [10], Ndambi et al. [11], Xia et al. [12], and Maia et al. [13]) and static deflections (Rucka and Wilde [14] and Pai and Young [15]), as well as on accumulated strain energy (Cornwell et al. [16] and Zhang et al. [17]).

Koo et al. [18] and Sung et al. [19] presented algorithms for the localization and quantification of damage in shear buildings by the calculation of static displacements based on the flexibility matrix which was verified by numerical and experimental studies. Zhu et al. [20] estimated damage in a shear building by means of the sensitivity analysis of the first derivative of the first mode shape data. They defined the first mode shape slope as a sensitive parameter in occurring single damage scenarios and then developed this hypothesis for multiple damage occurrences. Recently, Ghodrati Amiri et al. [21] described a damage detection method in shear frames by means of modal residual force and static deflections obtained by modal flexibility based on the diagonalization method.

Optimization algorithms are successful tools for damage identification methods. Many successful applications of damage detection using the genetic algorithm (GA) (Mares and Surace [22], Chou and Ghaboussi [23], Ananda Rao et al. [24], Perera and Torres [25], Vakil-Baghmisheh et al. [26], Gomes and Silva [27], Nobahari and Seyedpoor [28], and Amiri et al. [29]), particle swarm optimization (PSO) algorithm (Seyedpoor [30]), pattern search optimization method (Kourehli et al. [31]), simulated annealing optimization method (Kourehli et al. [32]), Big Bang-Big Crunch (BB-BC) algorithm (Tabrizian et al. [33]), and charged system search optimization (Kaveh and Maniat [34]) have been reported in the literature. Amiri et al. [29] described a damage detection method based on defining the damage detection problem as an optimization problem by using genetic and pattern search algorithms in order to detect damage in plate-like structures. Bagheri et al. [35] studied an optimization strategy for solving an inverse problem to estimate damage in different types of structures by defining a cost function based on modal data and a free vibration scheme of structures.

Although, the use of an optimization algorithm enables us to identify the structural damage, they impose much computational effort to the process due to a great number of damage variables. The mentioned approaches have some advantages; they have some disadvantages as well, the most important being that they cannot be used in real large structures such as high-rise buildings, because the computational time is not suitable. In order to reduce the computational cost of the optimization process, some useful techniques can be employed. A useful technique is to reduce the dimension of optimization problem by excluding the healthy elements firstly and then applying the optimization method to the reduced problem for determining the extent of damaged elements (Guo and Li [36] and Fallahian and Seyedpoor [37]).

In this study, an efficient indicator based on the story displacement index containing a local characteristic of the shear frame is introduced to locate the damage quickly and accurately. The story displacement index (SDI) is calculated using the modal analysis information of damaged structure. In the second stage, by defining a new objective function, the extent of actual damage is determined by optimizing the objective function via an imperialist competitive algorithm (ICA) using the first-stage results. The performance of the proposed method has been verified through using a benchmark problem provided by the IASC-ASCE Task Group on structural health monitoring and a number of numerical examples.

2. Damage Detection Method

2.1. Story Displacement Based Index

It is assumed that a unique static load such as Fo is applied to a shear frame with degrees of freedom. This load is defined asThe static equilibrium equation of a shear frame in its healthy state can be expressed as follows:where and are the stiffness matrix and displacement vector in healthy state, respectively. From (2), the vector static displacement of healthy structure can be presented asin which is the undamaged or healthy flexibility matrix. The flexibility matrix for a healthy structure can be written aswhere is the mode shape matrix and is a diagonal matrix whose members are the eigenvalues of the free vibration problem.

The static equilibrium equation of a shear frame in damaged state can be expressed as follows:where and are the stiffness matrix and displacement vector in damaged state, respectively. From (5), the damaged static displacement vector using the first modes data can be presented aswhere and are the displacement vector and flexibility matrix in damaged structure which are calculated using the first modes data, respectively. The flexibility matrix for a damaged structure can be written by considering modal data (natural frequencies and mode shapes) aswhere is the damaged mode shape matrix that includes the first damaged mode shape vectors and is a diagonal matrix whose members are the eigenvalues of the damaged free vibration problem. For story , the story displacement index is defined asAccording to (8), for a healthy story, the index will be equal to zero and, for a damaged story, the index will be greater than zero .

2.2. Objective Function

It is generally known that the eigenvalue equation of an undamaged or healthy structure is as follows (Chopra [38]):where is mass matrices in the undamaged or healthy structure and is the total number of vibration mode shapes obtained. Equation (9) becomes as follows:where and are damaged global stiffness matrix and healthy mass matrix, respectively and is the natural frequency corresponding to the vibration mode shape in damaged structures. To determine damage-induced alteration stiffness, in this study, we apply degradation in story stiffness as follows:where and are the damaged and healthy stiffness of the th story, respectively, and indicates the damage severity at the th story whose values are between 0 for a story without damage and 1 for a ruptured story. The damaged stiffness matrix for an -story shear building can be written as

By solving (10), calculating vibration frequencies and mode shapes in the system, the orthogonal conditions apply to any two different modes, as indicated in (13); they do not apply to two modes having the same frequency (Chopra [38]). ConsiderIn the process of substituting the measured mode shapes of the damaged structure into (13) for two different modes, a dynamic residue vector can be defined for two different measured mode shapes as follows:where and are the th and th mode shapes from measurements, respectively. If structural damage is determined correctly, the residue would be next to 0 in (14). For all of modes in model , we have orthogonal relationships, and then the objective function can be formulated as follows:where represents the Euclidean length of and is the number of stories in which their SDI is greater than 0.02 in stage 1 .

During modal testing, it is customary to assume that the frequencies of vibration are accurately determined and those are in the determination of the amplitudes of the mode shapes in which the experimental errors occur. This assumption is usually valid since the frequency of shakers, even at resonance, can be quite accurately controlled. So the calculated data is simulated to the experimental one by adding noise to each mode shape using the following equation (Udwadia [39]):where and are the th value of the th mode shape vector with noise and without noise, is the noise level (e.g., 0.05 relates to a 5% noise level), and is a uniformly distributed number between −1 and +1 which is generated by MATLAB software.

2.3. Imperialist Competitive Algorithm

Imperialism is the policy of spreading the power of an imperial beyond its own boundaries. An imperialist dominate other countries by direct rule or by less obvious means such as control of market for goods or raw materials. Imperialist competitive algorithm (ICA) is a new sociopolitically motivated global search strategy that has recently been introduced for dealing with different optimization tasks. ICA simulates the social-political process of imperialism and imperialist competition. This algorithm contains a population of agents or countries. Similar to the other evolutionary algorithms that start with initial populations, ICA begins with initial empires. Any individual of an empire is called a country. Some of the best countries are selected to be the imperialist states and all the other countries form the colonies of these imperialists. The colonies are divided among the mentioned imperialists based on their power. After dividing all colonies among imperialists and creating the initial empires, these colonies start moving toward their relevant imperialist state. This movement is a simple model of assimilation policy that was pursued by some imperialist states (Atashpaz-Gargari and Lucas [40]).

The aim is to find a set of damage variables minimizing the aswhere is the objective function that should be minimized. In order to minimize (17), the optimization algorithm is started by producing the initial countries of size . The primary locations of the countries are determined by the set of values assigned to each decision variable randomly aswhere determines the initial value of the th variable for the th country, and are the minimum and the maximum allowable values for the th variable, and rand is a random number in the interval . The most powerful countries are selected to form the empires. The remaining countries, , individually belong to an empire as the colonies. Note that the initial number of colonies assigned to an empire should be directly proportional to its normalized power. In order to proportionally divide the colonies among the imperialists, a normalized cost for an imperialist is defined aswhere is the cost of the th imperialist and is its normalized cost. The colonies are divided among empires based on their power or normalized cost and, for the th empire, it will be as follows:where is the initial number of colonies associated to the th empire which are selected randomly among the colonies. These colonies together with the th imperialist form the empire number . Then, after forming initial empires, the colonies in each of them start moving toward their relevant imperialist country. While moving toward the imperialist, a colony might reach a position with higher cost than that of imperialist. In this case, the imperialist and the colony change their positions. Then, the algorithm will continue by the imperialist in the new position and then colonies start moving toward this position.

After the exchanging step, calculate the total power of each empire, which depends on both the power of the imperialist country and the power of its colonies. Total power of an empire is mainly affected by the power of the imperialist country. But the power of the colonies of an empire has an effect, though negligible, on the total power of that empire. This fact is modeled by defining the total cost aswhere is the total cost of the th empire and is a positive number which is considered to be less than 1. The value of 0.1 for is found to be a suitable value in most of the implementations (Gargari et al. [41]). Similar to (19), the normalized total cost is defined aswhere is the normalized total cost of the th empire. Having the normalized total cost, the possession probability of each empire is evaluated bywhen an empire loses all of its colonies, it is assumed to be collapsed. In this model implementation, where the powerless empires collapse in the imperialist competition, the corresponding colonies will be divided among the other empires. Moving colonies toward imperialists are continued and imperialist competition and implementations are performed during the search process. When the number of iterations reaches a predefined value or the amount of improvement in the best result reduces to a predefined value, the searching process is stopped.

3. Numerical Examples

In this section, the efficiency of the presented method is investigated by studying 5-story, 10-story, and 25-story shear frames. In all numerical examples, damage in the structure is simulated as a relative reduction in the stiffness story. Studies are carried out within the MATLAB [42] environment, which is used for the solution of problems and optimization.

3.1. Five-Story Shear Frame

The five-story shear frame is shown in Figure 1 selected from [21]. The mass and stiffness are presented in Table 1. In the five-story shear frame, three different damage scenarios given in Table 2 are induced in the structure and the proposed method is tested for each scenario. In this example, the first two vibration modes are utilized for damage detection. Figures 2(a)–2(c) show the SDI value with respect to story number for damage scenarios 1–3, respectively. As shown in the figures, the most potentially damaged stories are as follows: story 2 for damage scenario 1; stories 1 and 4 for damage scenario 2; and stories 3 and 5 for damage scenario 3. Here, those stories whose indexes exceed 0.02 are selected as suspected damaged stories. It is revealed that the damage variables for scenarios 1 to 3 can be reduced from 5 to 1, 2, and 2 variables, respectively.

(a)

(b)

(c)

The ICA is now employed to solve the reduced damage detection problem to determine the damage sizes. In this example, a population of 20 countries consisting of 2 empires and 18 colonies is used. The presented method starts with a random initial population of countries. The cost of each solution is evaluated by computing the objective function. Thereafter, the assimilation changes the positions of the colony and the imperialist and imperialist competition are applied to obtain the solution to the problem. The damage identification results, using the objective function with noise (5% and 8%) and without noise for scenarios 1–3, are shown in Figures 3 to 5, respectively. The results illustrate that the proposed method can detect the location and the extent of damage very quickly and accurately. The convergence history of the ICA for scenario 2 is shown in Figure 6.

(a)

(b)

(a)

(b)

(a)

(b)

3.2. Ten-Story Shear Frame

The ten-story shear frame is shown in Figure 7. The mass and stiffness are presented in Table 3. In the ten-story shear frame, three different damage scenarios given in Table 4 are induced in the structure and the proposed method is tested for each scenario. In this example, the first four vibrating modes are utilized for damage detection. Figures 8(a)–8(c) show the SDI value with respect to story number for damage scenario 1–3, respectively. As shown in the figures, the most potentially damaged stories are as follows: story 5 for damage scenario 1; stories 2 and 8 for damage scenario 2; and stories 3, 5, and 10 for damage scenario 3. It is revealed that the damage variables for scenarios 1 to 3 can be reduced from 10 to 1, 2, and 3 variables, respectively.

(a)

(b)

(c)

The ICA is now employed to solve the reduced damage detection problem to determine the damage sizes. In this example, a population of 35 countries consisting of 5 empires and 30 colonies is used. The damage identification results, using the objective function with noise (5% and 8%) and without noise for scenarios 1–3, are shown in Figures 9 to 11, respectively. The convergence history of the ICA for scenario 3 is shown in Figure 12. The results illustrate that the proposed method can detect the location and the extent of damage very quickly and accurately.

(a)

(b)

(a)

(b)

(a)

(b)

3.3. 25-Story Shear Frame

The 25-story shear frame is selected from [21]. The mass and stiffness are presented in Table 5. In the 25-story shear frame, three different damage scenarios given in Table 6 are induced in the structure and the proposed method is tested for each scenario. In this example, the first five vibrating modes are utilized for damage detection. Figures 13(a)–13(c) show the SDI value with respect to story number for damage scenarios 1–3, respectively. As shown in the figures, the most potentially damaged stories are as follows: story 10 for damage scenario 1; stories 5 and 20 for damage scenario 2; and stories 7, 12, 14, and 25 for damage scenario 3. It is revealed that the damage variables for scenarios 1 to 3 can be reduced from 25 to 1, 2, and 4 variables, respectively. In this example, a population of 40 countries consisting of 5 empires and 35 colonies is used. The damage identification results for scenarios 1–3 are shown in Figures 14 to 16, respectively. The results illustrate that the proposed method can detect the location and the extent of damage very quickly and accurately. The convergence history of the ICA for scenario 3 is shown in Figure 17.

(a)

(b)

(c)

(a)

(b)

(a)

(b)

(a)

(b)

4. Experimental Verification Study

In the previous section, the proposed method was demonstrated through some numerical examples. However, it is useful to examine the experimental performance of the proposed method, using measured data from an experimental study. Therefore, in this section, the performance of the proposed damage detection method is verified through the benchmark structure. The benchmark structure is a four-story steel frame, two-bay by two-bay, and quarter-scale model structure constructed in the Earthquake Engineering Research Laboratory at the University of British Colombia. Geometry of the benchmark structure is shown in Figure 18. Details of the first phase of IASC-ASCE benchmark problem was presented by Johnson et al. 2004 [1] and also are available on IASC-ASCE Structural Health Monitoring Task Group’s website.

The proposed method was applied to case 1 of this phase benchmark problem, and the finite element model of the 12-DOF shear building model is used. In this study, the three following damage scenarios have been considered:(1)One brace of the first story is broken (scenario 1).(2)One brace at the first and third stories is broken (scenario 2).(3)1/3 of area of one brace at the first story is cut (scenario 3).

For each damage scenario, the mass and horizontal story stiffness are illustrated in Table 7.

Damage in the structures can be determined using the proposed method. In this example, the five three vibrating modes are utilized for damage detection. In this example, a population of 40 countries consisting of 5 empires and 35 colonies is used. Figures 19(a)–19(c) show the SDI value with respect to stiffness DOFs for damage scenarios 1–3, respectively. The results of the application of the proposed method to the benchmark structure are cited in Table 8. The convergence history of the ICA for scenarios 1–3 is shown in Figure 20. The results illustrate that the proposed method can detect the location and the extent of damage very quickly and accurately.

(a)

(b)

(c)

5. Conclusions

In this study, a new method is proposed to properly identify the location and the extent of damage in shear frames. The proposed method has two stages. In the first stage, a story displacement index (SDI) is presented to precisely locate the damage in the shear frame. The story displacement index is calculated using the modal analysis information of the damaged structure. In the second stage, by defining a new objective function using orthogonal conditions in mode shapes, the extent of the actual damage is determined via an imperialist competitive algorithm (ICA).

In order to assess the performance of the proposed method for structural damage detection, three examples, that is, 5-story shear frame, 10-story shear frame, and 25-story shear frame with noise (noise 5% and noise 8%) and without noise in modal data, are considered. To validate the efficiency and applicability of the proposed method, a study on the damage detection was conducted using the benchmark of the IASC-ASCE Task Group on Structural Health Monitoring. The obtained results indicated that the proposed method is a strong and viable method to the problem of detection and estimation of damage in the shear frames.

Conflict of Interests

The authors declare that there is no conflict of interests regarding the publication of this paper.

References

E. A. Johnson, H. F. Lam, L. S. Katafygiotis, and J. L. Beck, “Phase I IASC-ASCE structural health monitoring benchmark problem using simulated data,” Journal of Engineering Mechanics, vol. 130, no. 1, pp. 3–15, 2004.
View at: Publisher Site | Google Scholar
A. Zingoni, “Structural health monitoring, damage detection and long-term performance,” Engineering Structures, vol. 27, no. 12, pp. 1713–1714, 2005.
View at: Publisher Site | Google Scholar
A. Rytter, Vibration based inspection of civil engineering structures [Ph.D. thesis], Aalborg University, Aalborg, Denmark, 1993.
S. W. Doebling, C. R. Farrar, M. B. Prime, and D. W. Shevitz, “Damage identification and health monitoring of structural and mechanical systems from changes in their vibration characteristics: a literature review,” Report LA-13070-MS, Los Alamos National Laboratory, Los Alamos, NM, USA, 1996.
View at: Google Scholar
H. Sohn, C. R. Farrar, F. M. Hemez, D. D. Shunk, D. W. Stinemates, and B. R. Nadler, “A review of structural health monitoring literature: 1996–2001,” Los Alamos National Laboratory Report LA-13976-MS, Los Alamos National Laboratory, 2003.
View at: Google Scholar
O. S. Salawu, “Detection of structural damage through changes in frequency: a review,” Engineering Structures, vol. 19, no. 9, pp. 718–723, 1997.
View at: Publisher Site | Google Scholar
S. Hassiotis and G. D. Jeong, “Identification of stiffness reductions using natural frequencies,” Journal of Engineering Mechanics, vol. 121, no. 10, pp. 1106–1113, 1995.
View at: Publisher Site | Google Scholar
D. Capecchi and F. Vestroni, “Monitoring of structural systems by using frequency data,” Earthquake Engineering and Structural Dynamics, vol. 28, no. 5, pp. 447–461, 1999.
View at: Publisher Site | Google Scholar
Y. Xia and H. Hao, “Statistical damage identification of structures with frequency changes,” Journal of Sound and Vibration, vol. 263, no. 4, pp. 853–870, 2003.
View at: Publisher Site | Google Scholar
J. Maeck and G. De Roeck, “Dynamic bending and torsion stiffness derivation from modal curvatures and torsion rates,” Journal of Sound and Vibration, vol. 225, no. 1, pp. 153–170, 1999.
View at: Publisher Site | Google Scholar
J.-M. Ndambi, J. Vantomme, and K. Harri, “Damage assessment in reinforced concrete beams using eigenfrequencies and mode shape derivatives,” Engineering Structures, vol. 24, no. 4, pp. 501–515, 2002.
View at: Publisher Site | Google Scholar
Y. Xia, H. Hao, J. M. W. Brownjohn, and P.-Q. Xia, “Damage identification of structures with uncertain frequency and mode shape data,” Earthquake Engineering & Structural Dynamics, vol. 31, no. 5, pp. 1053–1066, 2002.
View at: Publisher Site | Google Scholar
N. M. M. Maia, J. M. M. Silva, E. A. M. Almas, and R. P. C. Sampaio, “Damage detection in structures: from mode shape to frequency response function methods,” Mechanical Systems and Signal Processing, vol. 17, no. 3, pp. 489–498, 2003.
View at: Publisher Site | Google Scholar
M. Rucka and K. Wilde, “Crack identification using wavelets on experimental static deflection profiles,” Engineering Structures, vol. 28, no. 2, pp. 279–288, 2006.
View at: Publisher Site | Google Scholar
P. F. Pai and L. G. Young, “Damage detection of beams using operational deflection shapes,” International Journal of Solids and Structures, vol. 38, no. 18, pp. 3161–3192, 2001.
View at: Publisher Site | Google Scholar
P. Cornwell, S. W. Doebling, and C. R. Farrar, “Application of the strain energy damage detection method to plate-like structures,” in Proceedings of the 15th International Modal Analysis Conference (IMAC '97), pp. 1312–1318, Orlando, Fla, USA, February 1997.
View at: Google Scholar
D. Zhang, W. Quiong, and M. Link, “A structural damage identification approach based on element modal strain energy,” in Proceedings of the ISMA 23rd International Conference on Noise and Vibration Engineering, Leuven, Belgium, September 1998.
View at: Google Scholar
K. Y. Koo, S. H. Sung, and H. J. Jung, “Damage quantification of shear buildings using deflections obtained by modal flexibility,” Smart Materials and Structures, vol. 20, no. 4, Article ID 045010, 2011.
View at: Publisher Site | Google Scholar
S. H. Sung, K. Y. Koo, H. Y. Jung, and H. J. Jung, “Damage-induced deflection approach for damage localization and quantification of shear buildings: validation on a full-scale shear building,” Smart Materials and Structures, vol. 21, no. 11, Article ID 115013, 2012.
View at: Publisher Site | Google Scholar
H. Zhu, L. Li, and X.-Q. He, “Damage detection method for shear buildings using the changes in the first mode shape slopes,” Computers & Structures, vol. 89, no. 9-10, pp. 733–743, 2011.
View at: Publisher Site | Google Scholar
G. Ghodrati Amiri, A. Z. Hosseinzadeh, A. Bagheri, and K.-Y. Koo, “Damage prognosis by means of modal residual force and static deflections obtained by modal flexibility based on the diagonalization method,” Smart Materials and Structures, vol. 22, no. 7, Article ID 075032, 2013.
View at: Publisher Site | Google Scholar
C. Mares and C. Surace, “An application of genetic algorithms to identify damage in elastic structures,” Journal of Sound and Vibration, vol. 195, no. 2, pp. 195–215, 1996.
View at: Publisher Site | Google Scholar
J.-H. Chou and J. Ghaboussi, “Genetic algorithm in structural damage detection,” Computers & Structures, vol. 79, no. 14, pp. 1335–1353, 2001.
View at: Publisher Site | Google Scholar
M. Ananda Rao, J. Srinivas, and B. S. N. Murthy, “Damage detection in vibrating bodies using genetic algorithms,” Computers and Structures, vol. 82, no. 11-12, pp. 963–968, 2004.
View at: Publisher Site | Google Scholar
R. Perera and R. Torres, “Structural damage detection via modal data with genetic algorithms,” Journal of Structural Engineering, vol. 132, no. 9, pp. 1491–1501, 2006.
View at: Publisher Site | Google Scholar
M.-T. Vakil-Baghmisheh, M. Peimani, M. H. Sadeghi, and M. M. Ettefagh, “Crack detection in beam-like structures using genetic algorithms,” Applied Soft Computing Journal, vol. 8, no. 2, pp. 1150–1160, 2008.
View at: Publisher Site | Google Scholar
H. M. Gomes and N. R. S. Silva, “Some comparisons for damage detection on structures using genetic algorithms and modal sensitivity method,” Applied Mathematical Modelling, vol. 32, no. 11, pp. 2216–2232, 2008.
View at: Publisher Site | Google Scholar
M. Nobahari and S. M. Seyedpoor, “Structural damage detection using an efficient correlation-based index and a modified genetic algorithm,” Mathematical and Computer Modelling, vol. 53, no. 9-10, pp. 1798–1809, 2011.
View at: Publisher Site | Google Scholar
G. G. Amiri, S. A. S. Razzaghi, and A. Bagheri, “Damage detection in plates based on pattern search and Genetic algorithms,” Smart Structures and Systems, vol. 7, no. 2, pp. 117–132, 2011.
View at: Publisher Site | Google Scholar
S. M. Seyedpoor, “A two stage method for structural damage detection using a modal strain energy based index and particle swarm optimization,” International Journal of Non-Linear Mechanics, vol. 47, no. 1, pp. 1–8, 2012.
View at: Publisher Site | Google Scholar
S. S. Kourehli, G. G. Amiri, M. Ghafory-Ashtiany, and A. Bagheri, “Structural damage detection based on incomplete modal data using pattern search algorithm,” Journal of Vibration and Control, vol. 19, no. 6, pp. 821–833, 2013.
View at: Publisher Site | Google Scholar
S. S. Kourehli, A. Bagheri, G. G. Amiri, and M. Ghafory-Ashtiany, “Structural damage detection using incomplete modal data and incomplete static response,” KSCE Journal of Civil Engineering, vol. 17, no. 1, pp. 216–223, 2013.
View at: Publisher Site | Google Scholar
Z. Tabrizian, E. Afshari, G. G. Amiri, M. H. Ali Beigy, and S. M. P. Nejad, “A new damage detection method: Big Bang-Big Crunch (BB-BC) algorithm,” Shock and Vibration, vol. 20, no. 4, pp. 633–648, 2013.
View at: Publisher Site | Google Scholar
A. Kaveh and M. Maniat, “Damage detection in skeletal structures based on charged system search optimization using incomplete modal data,” International Journal of Civil Engineering, vol. 12, no. 2, pp. 193–200, 2014.
View at: Google Scholar
A. Bagheri, H. R. Razeghi, and G. G. Amiri, “Detection and estimation of damage in structures using imperialist competitive algorithm,” Shock and Vibration, vol. 19, no. 3, pp. 405–419, 2012.
View at: Publisher Site | Google Scholar
H. Y. Guo and Z. L. Li, “A two-stage method to identify structural damage sites and extents by using evidence theory and micro-search genetic algorithm,” Mechanical Systems and Signal Processing, vol. 23, no. 3, pp. 769–782, 2009.
View at: Publisher Site | Google Scholar
S. Fallahian and S. M. Seyedpoor, “A two stage method for structural damage identification using an adaptive neuro-fuzzy inference system and particle swarm optimization,” Asian Journal of Civil Engineering (Building and Housing), vol. 11, no. 6, pp. 797–810, 2010.
View at: Google Scholar
A. K. Chopra, Dynamics of Structures in Theory and Applications to Earthquake Engineering, Prentice Hall, Berkeley, Calif, USA, 4th edition, 2007.
F. E. Udwadia, “Structural identification and damage detection from noisy modal data,” Journal of Aerospace Engineering, vol. 18, no. 3, pp. 179–187, 2005.
View at: Publisher Site | Google Scholar
E. Atashpaz-Gargari and C. Lucas, “Imperialist competitive algorithm: an algorithm for optimization inspired by imperialistic competition,” in Proceedings of the IEEE Congress on Evolutionary Computation (CEC '07), pp. 4661–4667, Singapore, September 2007.
View at: Publisher Site | Google Scholar
E. A. Gargari, F. Hashemzadeh, R. Rajabioun, and C. Lucas, “Colonial competitive algorithm: a novel approach for PID controller design in MIMO distillation column process,” International Journal of Intelligent Computing and Cybernetics, vol. 1, no. 3, pp. 337–355, 2008.
View at: Publisher Site | Google Scholar | MathSciNet
MATLAB, Matlab User Manual, MathWork, Lowell, Mass, USA, 2008.

Copyright

Copyright © 2015 Asghar Rasouli et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies