Octaband WWAN/LTE Dual-Antenna System Decoupled by Two Neutralization Lines with Inductors for Smart Phones

Wang, Yan; Du, Zhengwei

doi:https://doi.org/10.1155/2021/1609263

International Journal of Antennas and Propagation

On this page

Abstract Introduction Conclusions Data Availability Conflicts of Interest References Copyright Related Articles

Research Article | Open Access

Volume 2021 | Article ID 1609263 | https://doi.org/10.1155/2021/1609263

Octaband WWAN/LTE Dual-Antenna System Decoupled by Two Neutralization Lines with Inductors for Smart Phones

Yan Wang¹and Zhengwei Du²

Academic Editor: Stefano Selleri

Received18 Jul 2021

Revised06 Nov 2021

Accepted25 Nov 2021

Published06 Dec 2021

Abstract

A decoupled octaband WWAN/LTE dual-antenna system occupying a size of 80 mm × 15 mm × 6.8 mm for smart phones is proposed. The proposed antenna system consists of two antenna elements with symmetrical geometry, two neutralization lines (NLs) with embedded inductor, and an inverted-T branch. The two NLs mainly reduce the mutual coupling at the desired lower (704–960 MHz) frequency band, while the inverted-T branch mainly reduces the mutual coupling at the desired higher (1710–2690 MHz) frequency band. The fabricated prototype has a −6 dB impedance bandwidth of 0.3 GHz (0.69–0.99 GHz) and 1.2 GHz (1.66–2.86 GHz) which cover the LTE700, GSM850, GSM900, DCS, PCS, UMTS, LTE2300, and LTE2500 bands. Within these bands, the measured mutual couplings are lower than −10 dB. The measured antenna efficiencies are about 42.6%–60% and 58.3%–78.7% at the desired lower and higher frequency bands, respectively. The diversity performance and the SAR performance are also evaluated.

1. Introduction

Multi-input and multi-output (MIMO) is one of the critical techniques for the fifth-generation (5G) mobile communication [1]. For a MIMO system, the good performance comes from the multiple antennas with a low correlation [2]. That is, low mutual coupling among the multiple antennas is requested. Nevertheless, because most of the spaces in smart phones are reserved for the display, cameras, battery, and PCB, only small spaces are left to design antenna [3]. Thus, designing multiple antennas with low mutual coupling in the limited space of smart phones is very challenging.

The open literature has proposed some efficient methods to reduce the mutual coupling. For example, orthogonal polarization [4], orthogonal pattern [5], orthogonal phase [6], and orthogonal modes [7] are proposed. In [8], the loop antenna loaded with a lumped capacitor could be applied to isolate the two antenna elements. In [9], a metasurface above the antenna array is studied. Separating discrete antenna element with certain distance can also achieve low mutual coupling [10, 11]. Also, the concept of common mode and differential mode is studied to reduce the mutual coupling in [12, 13]. In addition, the decoupling network [14], grounded branch [15], parasitic element [16], and neutralization line [17] could introduce a new coupling to reduce the mutual coupling. Although the above methods are promising for practical applications, most of them usually reduce the mutual coupling at the higher frequency band above 1.7 GHz.

For the frequency bands lower than 1 GHz, which is very important for the operators to realize the wide area coverage, the antenna size related to the wavelength is very small. Thus, decoupling the dual-antenna working at these bands is more challenge [18]. To address this challenge, the theory of characteristic mode is applied [18, 19]. In [20, 21], the neutralization line was applied to decouple two antennas operating at the LTE700 (704–787 MHz)/LTE2500 (2500–2690 MHz) bands [20] and the GSM850 (824–894 MHz)/GSM900 (880–960 MHz)/DCS (1710–1880 MHz)/PCS (1850–1990 MHz)/UMTS (1920–2170 MHz)/LTE2300 (2300–2400 MHz)/LTE2500 bands [21]. In [22, 23], to cover all the eight bands (LTE700/GSM850/GSM900/DCS/PCS/UMTS/LTE2300/LTE2500), the crossed neutralization line [22] and the folded fork-shaped grounded branch [23] are proposed. However, the antenna efficiency in [22, 23] at the lower band is only 32% which is a bit low for practical applications.

In this letter, we propose another octaband dual-antenna system covering the LTE700, GSM850, GSM900, DCS, PCS, UMTS, LTE2300, and LTE2500 bands with the antenna efficiency of higher than 42%. To better show the contribution of the proposed design, Table 1 compares the figures of merit of some typical dual-antenna systems. For the mobile antenna, the higher efficiency with wide bandwidth is very important and useful for practical applications. The main contribution is that the proposed dual-antenna system could cover all the WWAN/LTE bands with higher efficiency. This letter is organized as follows. Section 2 describes the antenna geometry. In Section 3, the working mechanism is analyzed. The measured results are illustrated in Section 4. Finally, Section 5 summaries this paper.

2. Antenna Configuration with Detailed Dimensions

The geometry of the dual-antenna system with detailed dimensions is given in Figure 1. As seen in Figure 1(a), the dual-antenna system is located at the top part of the printed circuit board (PCB). The substrate of the PCB is a 0.8 mm thick FR4-epoxy with a length of 155 mm and a width of 80 mm. Its relative permittivity is 4.4 and its loss tangent is 0.02. A ground plane with a size of 140 mm × 80 mm, which simulates a 5.7-inch display, is printed on the bottom layer.

(a)

(b)

(c)

The detailed dimensions with the front and back views are shown in Figures 1(b) and Figure 1, respectively. The antenna element of the dual antenna, evolving from the design in [24] for heptaband applications, consists of a coupled-fed loop strip and a chip-inductor-loaded strip. The coupled-fed loop strip, comprising an L-shape feeding strip (section AB) and a coupled loop strip (section CDG), mainly contributes to the higher frequency band. The chip-inductor-loaded strip, which mainly contributes to the lower frequency band, consists of a chip inductor (L1) and a folded metal strip (section EF). The folded metal strip is made up of a printed metal pattern on the bottom layer of the PCB and a folded copper plate (showing in yellow). The folded copper plate is a thin copper sheet which is supported by a foam. In Figure 1, the foam is omitted for better view.

To address the strong mutual coupling among the two elements, the neutralization line 1 (NL1, bottom layer of the PCB), neutralization line 2 (NL2, top layer of the PCB), and inverted-T branch (connecting to the ground at the bottom layer of the PCB) are introduced. NL1 and NL2 are embedded with chip inductors L2 and L3, respectively. Note that, there are two inductors L3 on the NL2. At last, to test the antenna, two 50-Ω microstrip feeding lines with the 1.5 mm width are printed on the top layer of the PCB.

3. Working Mechanism of the Dual-Antenna System

To study the proposed antenna, the decoupling method of the two neutralizations (NL) with the embedded inductor and the inverted-T branch is analyzed. Then, the working mechanism of the decoupling method is studied based on the current distributions. Finally, the effect of the embedded inductors is studied for better understanding. It should be noted that the inductors (L1, L2, and L3) in Figure 1 are set to be ideal inductor in simulations.

3.1. Function of the Two NLs and the Inverted-T Branch

To analyze the proposed antenna, the S-parameters of the dual-antenna system without the two NLs and inverted-T branch (Ant1), the dual-antenna system with only the two NLs (Ant2), and the dual-antenna system (the Proposed Ant) are illustrated in Figure 2. From Figure 2(b), one can find that S21 of Ant1 are higher and lower than −10 dB at the desired lower (704–960 MHz) and higher (1710–2690 MHz) frequency bands, respectively. As the two NLs are applied, S21 of Ant2 at the desired lower frequency band (704–960 MHz) is reduced significantly. However, S21 of Ant2 at the 1.71–1.93 GHz band is increased to higher than −10 dB. When the inverted-T branch is applied, S21 of the Proposed Ant at the desired higher frequency band (1710–2690 MHz) is reduced to less than −10 dB. Also, Figure 2(a) shows that the two NLs and the inverted-T branch have some small effects on S11. So, the two NLs and the inverted-T branch are mainly used to reduce the mutual couplings at the lower (704–960 MHz) and higher (1710–2690 MHz) frequency bands, respectively.

To study the function of each NL, the S-parameters of the proposed antenna without NL2 (Ant3), the proposed antenna without NL1 (Ant4), and the proposed antenna (the Proposed Ant) are shown in Figure 3. Figure 3(a) illustrates that NL1 and NL2 have some effects on S11. Figure 3(b) shows that when NL1 or NL2 is applied alone, S21 of Ant3 and Ant4 have a deep point at about 0.79 GHz and 0.92 GHz, respectively. So, NL1 or NL2, when used alone, could decouple the dual-antenna system with a narrow bandwidth. When NL1 and NL2 are applied simultaneously, S21 of the Proposed Ant has two deep points at 0.73 and 0.88 GHz. Combining these two deep points, low mutual coupling within the wide band is achieved.

3.2. Current Distributions of Ant1, Ant2, and Proposed Ant

To analyze the working mechanism of the two NLs and the inverted-T branch, the scalar current distributions of Ant1, Ant2, and Proposed Ant at 0.73, 0.88, 1.8, and 2.5 GHz are illustrated in Figure 4. From Figure 4(a), it shows that the coupling current between the two antenna elements of Ant1 are strong and weak at the 0.73/0.88 GHz and the 1.8/2.5 GHz, respectively. As shown in Figure 4(b), when the two NLs are applied, the two NLs add new coupling current between the two antenna elements to reduce the mutual coupling [17]. Thus, the coupling current between the two antenna elements of Ant2 at 0.73/0.88 GHz are weakened. However, the coupling current of Ant2 at the 1.8/2.5 GHz is strengthened. Figure 4(c) shows that, when the inverted-T branch is applied, the coupling current between the two antenna elements of Proposed Ant is weakened. In addition, Figures 4(b) and 4(c) show that NL1 and NL2 mainly introduce new current paths at 0.73 GHz and 0.88 GHz, respectively.

3.3. Effect of the Embedded Inductors on the Mutual Coupling

In [17], the equivalent model of the neutralization line is established to analyze the working mechanism of the neutralization. Moving the neutralization line to the open end of antenna, increasing the width of the neutralization line, or increasing the length of the neutralization line can move the notch of the S21 to the lower frequency. The equivalent model in [17] can guide the design of neutralization line to be more intuitively. Here, to apply the neutralization line to decouple the dual-antenna system at the lower frequency band (704–960 MHz), the inductors are embedded to the neutralization line. The inductors can lengthen the electrical length of the neutralization line which can move the notch of the S21 to the lower frequency band.

To better show the function of the embedded inductors, the effect of the embedded inductors on the decoupling performance is analyzed. Figures 5 and 6 show the S-parameters of the proposed antenna with different values of L2 and L3. From Figures 5(b) and 6(b), one can find that increasing the values of L2 and L3 would decrease the decoupling frequencies of NL1 and NL2, respectively. This phenomenon comes from the fact that increasing the values of L2 and L3 can lengthen the electrical length of the neutralization line. Thus, decoupling within the desired lower frequency band could be achieved by fine tuning the values of L2 and L3. Figures 5(a) and 6(a) show that the values of L2 and L2 have some effect the antenna impedance.

(a)

(b)

(a)

(b)

To study the antenna performance with practical environment, the effects of the chassis ground plane and the size of the ground plane on the antenna performance are analyzed. Figure 7 shows the installation positions of the chassis ground plane. The size of the chassis ground plane is 130 mm × 80 mm × 2 mm. The distance between the chassis ground plane and the ground plane is 2 mm. Nine shorting pins are installed to connect the ground plane and the chassis ground. d determines the distance between the antenna and the chassis ground. Figure 8 shows the effect of the parameter d on the S-parameters. From Figure 8, one can find that if the chassis ground plane is installed on the mobile terminal, the S-parameters are affected a bit. As the distance between the antenna and the chassis ground plane increases, the effect decreases gradually. This phenomenon comes from that fact that, as the chassis ground plane is close to the antenna, it changes the coupling between the antenna and the ground plane. To further analyze the effect of the size of the ground plane on the antenna performance, Figure 9 shows the effect of the ground length on the S-parameters. Note that the results in Figure 9 are achieved without the chassis ground plane. From Figure 9, one can find that the length of the ground has some effects on the S-parameters at the lower frequency band while has a slight effect at the higher frequency band. The effect at the lower frequency band could be mitigated by fine tuning the antenna parameters.

(a)

(b)

(a)

(b)

4. Experimental Results of the Proposed Antenna

Based on the above analyses, an antenna prototype using the antenna geometry with dimensions in Figure 1 is manufactured. The keysight vector network analyzer E5071B is used to test the S-parameters. The ETS-Lindgren AMS8500 anechoic chamber is used to test the radiation performance.

4.1. S-Parameters

The measured and simulated S-parameters of the proposed decoupled dual-antenna system are given in Figure 10. The measured impedance bandwidths with S11 < −6 dB reach 0.3 GHz (0.69–0.99 GHz) and 1.2 GHz (1.66–2.86 GHz). Between 0.69–0.99 GHz and 1.66–2.76 GHz bands, the measured S21 are lower than −10 dB. The corresponding simulated impedance bandwidths are 0.36 GHz (0.63–0.99 GHz) and 1.48 GHz (1.61–3.09 GHz). Between 0.7–0.99 GHz and 1.61–3.09 GHz, the simulated S21 are lower than −10 dB. Both the simulated and measured bandwidths with S11 < −6 dB and S21 < −10 dB could cover the desired working bands of LTE700, GSM850, GSM900, DCS, PCS, UMTS, LTE2300, and LTE2500. The differences between the simulated and measured S-parameters might come from the simulated and measured errors.

4.2. Radiation Performance

The measured three-dimensional (3D) radiation patterns of the proposed antenna at the 0.75, 0.85, 0.95, 1.8, 2.2, and 2.6 GHz are shown in Figures 11 and 12 which illustrate the simulated and measured total antenna gains and efficiencies. From Figure 11, one can find that the two antenna elements of the proposed dual-antenna system could radiate power to complementary space. Figure 12 shows that the measured total antenna efficiencies are about 42.6%–60% and 58.3%–78.7% at the lower (704–960 MHz) and higher (1710–2690 MHz) frequency bands, respectively. The simulated ones are about 50%–56% and 50.4%–71.2%. The measured antenna gains are about −0.69–0.31 dBi and 1.2–5.6 dBi at the lower (704–960 MHz) and higher (1710–2690 MHz) frequency bands, respectively. The simulated ones are about −0.22–0.58 dBi and 1.7–4.4 dBi. The differences between the simulated and measured results might come from the simulated error, the measured error, and the manufacture error.

(a)

(b)

4.3. Diversity Performance

The envelop correlation coefficient (ρ_e) and mean effective gain (MEG) are two important criterions to evaluate the performance of a multiantenna system.

ρ_e is the correlation of the signals received by two different elements. Supposing the reflection and diffraction are rich, the channel response is Rayleigh-distributed, and the multipath signal is 3D uniform distributed in a full sphere, the complex correlation coefficient (ρ_c), and the envelop correlation coefficient (ρ_e) can be evaluated as [25]wherewhere E_θ and E_ϕ are the θ- and ϕ-components of the complex electrical field, respectively, p_θ and p_ϕ are the θ- and ϕ-components of the probability distribution function of the incoming wave, respectively, and Γ is the cross-polarization discrimination (XPD) (ratio of vertical to horizontal power density) of the incident filed. In this paper, Γ of 0 dB and 6 dB, which are the average values in an indoor and an urban fading environment [25], respectively, and are assumed.

MEG, representing the mean power received from each element, is the ratio of the mean received power of each element to the mean incident power. It can be obtained from the radiation patterns and the statistics of the channel as [26, 27]where G_θ and G_ϕ are the θ- and ϕ-polarized components of the antenna power gain pattern.

According to (1) and (3), ρ_e and MEG are calculated using the measured 3D radiation patterns. The evaluated ρ_e and MEG are shown in Figure 13. As can be seen from Figure 13, in the indoor (Γ = 0 dB) or the urban (Γ = 6 dB) fading environment, the envelop correlation coefficient at the lower frequency band and the higher frequency band is lower than 0.22 and 0.21, respectively. The ratio of the mean effective gain at the lower frequency band and the higher frequency band is lower than 0.26 dB and 0.4 dB, respectively. In summary, the diversity performance of the proposed dual-antenna system satisfies the criterions of low correlation (ρ_e is lower than 0.5) and comparable average received power (|MEG₁-MEG₂| is lower than 3 dB) [27].

4.4. SAR Performance

To study the specific absorption rate (SAR) of the proposed dual-antenna system to investigate the safety concerns of the user, Figure 14 shows the SAR simulation model of the proposed dual-antenna system. In the simulation model, the dual-antenna system is placed near the head phantom ear with a distance of 1 mm and is inclined to the vertical line by 60 degrees. To reduce the SAR, the dual-antenna system is located at the bottom part of the mobile phone. For SAR testing, the input power is 24 dBm (0.25 W) for 740 MHz, 860 MHz, and 925 MHz and 21 dBm (0.125 W) for 1795 MHz, 1920 MHz, 2045 MHz, 2350 MHz, and 2595 MHz. The simulated 10-g SAR values are listed in Table 2. Note that, in Table 2, the SAR values are achieved under the condition that one port is excited while the other one is terminated to a 50-Ω matching load. Table 2 shows the SAR values for the proposed dual-antenna system are below the SAR limit of 2.0 W/kg for 10 g tissue which is acceptable for practical applications [28].

5. Conclusions

This study presents an octaband WWAN/LTE dual-antenna system for smart phones. The proposed antenna system consists of two antenna elements with symmetrical geometry, two NLs with an embedded inductor and an inverted-T branch. The S-parameters with different geometries and scalar current distribution of the proposed antenna is applied to analyze the working mechanism. A fabricated prototype has the measured −6 dB impedance bandwidths covering all the desired frequency bands of LTE700, GSM850, GSM900, DCS, PCS, UMTS, LTE2300, and LTE2500 bands. Also, within these frequency bands, the measured mutual couplings are lower than −10 dB. Measured 3D radiation patterns cover symmetrical space. The measured efficiency is higher than 42% which is acceptable for practical applications. The diversity performance of the proposed dual-antenna system satisfies the criterions of low correlation and comparable average received power. The SAR performance is acceptable for practical applications. The moderate antenna size with high efficiency could be applied for the low-end mobile terminals.

Data Availability

No data were used to support this study.

Conflicts of Interest

The authors declare that they have no conflicts of interest.

References

J. G. Andrews, S. Buzzi, W. Choi et al., “What will 5G Be?” IEEE Journal on Selected Areas in Communications, vol. 32, no. 6, pp. 1065–1082, Jun. 2014.
View at: Publisher Site | Google Scholar
Z. Zhang, Antenna Design for Mobile Devices, Wiley, Hoboken, NJ, USA, 2nd edition, 2017.
W. Hong, “Solving the 5G mobile antenna puzzle: assessing future directions for the 5G mobile antenna paradigm shift,” IEEE Microwave Magazine, vol. 18, no. 7, pp. 86–102, 2017.
View at: Publisher Site | Google Scholar
L. Chang, Y. Yu, K. Wei, and H. Wang, “Polarization-orthogonal Co-frequency dual antenna pair suitable for 5G MIMO smartphone with metallic bezels,” IEEE Transactions on Antennas and Propagation, vol. 67, no. 8, pp. 5212–5220, 2019.
View at: Publisher Site | Google Scholar
C. Deng, X. Lv, and Z. Feng, “Wideband dual-mode patch antenna with compact CPW feeding network for pattern diversity application,” IEEE Transactions on Antennas and Propagation, vol. 66, no. 5, pp. 2628–2633, 2018.
View at: Publisher Site | Google Scholar
L. Sun, Y. Li, Z. Zhang, and M. F. Iskander, “A compact planar omnidirectional MIMO array antenna with pattern phase diversity using folded dipole element,” IEEE Transactions on Antennas and Propagation, vol. 67, no. 3, pp. 1688–1696, 2019.
View at: Publisher Site | Google Scholar
A. Ren, Y. Liu, and C.-Y.-D. Sim, “A compact building block with two shared-aperture antennas for eight-antenna MIMO array in metal-rimmed smartphone,” IEEE Transactions on Antennas and Propagation, vol. 67, no. 10, pp. 6430–6438, 2019.
View at: Publisher Site | Google Scholar
K. L. Wong, B. W. Lin, and S. E. Lin, “High‐isolation conjoined loop multi‐input multi‐output antennas for the fifth‐generation tablet device,” Microwave and Optical Technology Letters, vol. 61, no. 1, pp. 111–119, 2019.
View at: Publisher Site | Google Scholar
K.-L. Wu, C. Wei, X. Mei, and Z.-Y. Zhang, “Array-antenna decoupling surface,” IEEE Transactions on Antennas and Propagation, vol. 65, no. 12, pp. 6728–6738, 2017.
View at: Publisher Site | Google Scholar
A. Zhao, Z. Ren, and S. Wu, “broadband MIMO antenna system for 5G operations in mobile phones,” International Journal of RF and Microwave Computer-Aided Engineering, vol. 29, Article ID e21857, 2019.
View at: Publisher Site | Google Scholar
D. Huang, Z. Du, and Y. Wang, “Slot antenna array for fifth generation metal frame mobile phone applications,” International Journal of RF and Microwave Computer-Aided Engineering, vol. 29, Article ID e21841, 2019.
View at: Publisher Site | Google Scholar
L. Sun, Y. Li, Z. Zhang, and H. Wang, “Self-decoupled MIMO antenna pair with shared radiator for 5G smartphones,” IEEE Transactions on Antennas and Propagation, vol. 68, no. 5, pp. 3423–3432, 2020.
View at: Publisher Site | Google Scholar
H. Xu, S. S. Gao, H. Zhou, H. Wang, and Y. Cheng, “A highly integrated MIMO antenna unit: differential/common mode design,” IEEE Transactions on Antennas and Propagation, vol. 67, no. 11, pp. 6724–6734, 2019.
View at: Publisher Site | Google Scholar
J. Kornprobst, T. J. Mittermaier, R. A. M. Mauermayer et al., “Compact uniform circular quarter-wavelength monopole antenna arrays with wideband decoupling and matching networks,” IEEE Transactions on Antennas and Propagation, vol. 69, no. 2, pp. 769–783, 2021.
View at: Publisher Site | Google Scholar
D. Huang, Z. Du, and Y. Wang, “Dual antenna system for metal frame mobile phone applications,” International Journal of RF and Microwave Computer-Aided Engineering, vol. 30, Article ID e22110, 2020.
View at: Publisher Site | Google Scholar
L. Zhao and K.-L. Wu, “A decoupling technique for four-element symmetric arrays with reactively loaded dummy elements,” IEEE Transactions on Antennas and Propagation, vol. 62, no. 8, pp. 4416–4421, 2014.
View at: Publisher Site | Google Scholar
Y. Wang and Z. Du, “A wideband printed dual-antenna with three neutralization lines for mobile terminals,” IEEE Transactions on Antennas and Propagation, vol. 62, no. 3, pp. 1495–1500, 2014.
View at: Publisher Site | Google Scholar
H. Li, Z. T. Miers, and B. K. Lau, “Design of orthogonal MIMO handset antennas based on characteristic mode manipulation at frequency bands below 1 GHz,” IEEE Transactions on Antennas and Propagation, vol. 62, no. 5, pp. 2756–2766, 2014.
View at: Publisher Site | Google Scholar
C. Deng, Z. Feng, and S. V. Hum, “MIMO mobile handset antenna merging characteristic modes for increased bandwidth,” IEEE Transactions on Antennas and Propagation, vol. 64, no. 7, pp. 2660–2667, 2016.
View at: Publisher Site | Google Scholar
I. Dioum, A. Diallo, S. M. Farssi, and C. Luxey, “A novel compact dual-band LTE antenna-system for MIMO operation,” IEEE Transactions on Antennas and Propagation, vol. 62, no. 4, pp. 2291–2296, 2014.
View at: Publisher Site | Google Scholar
Y.-L. Yong-Ling Ban, Z.-X. Zhong-Xiang Chen, Z. Zhi Chen, K. Kai Kang, and J. L.-W. Li, “Decoupled hepta-band antenna array for WWAN/LTE smartphone applications,” IEEE Antennas and Wireless Propagation Letters, vol. 13, pp. 999–1002, 2014.
View at: Publisher Site | Google Scholar
S. Shang Wang and Z. Zhengwei Du, “Decoupled dual-antenna system using crossed neutralization lines for LTE/WWAN smartphone applications,” IEEE Antennas and Wireless Propagation Letters, vol. 14, pp. 523–526, 2015.
View at: Publisher Site | Google Scholar
S. Wang and Z. Du, “A multiband dual-antenna system with a folded fork-shaped ground branch and folded asymmetric U-shaped slots for smartphone applications,” IEEE Antennas and Wireless Propagation Letters, vol. 14, pp. 1626–1629, 2015.
View at: Publisher Site | Google Scholar
K.-L. Wong, M.-F. Tu, C.-Y. Wu, and W.-Y. Li, “On-board 7-band WWAN/LTE antenna with small size and compact integration with nearby ground plane in the mobile phone,” Microwave and Optical Technology Letters, vol. 52, no. 12, pp. 2847–2853, 2010.
View at: Publisher Site | Google Scholar
S. C. K. Ko and R. D. Murch, “Compact integrated diversity antenna for wireless communications,” IEEE Transactions on Antennas and Propagation, vol. 49, no. 6, pp. 954–960, 2001.
View at: Publisher Site | Google Scholar
R. G. Vaughan and J. B. Andersen, “Antenna diversity in mobile communications,” IEEE Transactions on Vehicular Technology, vol. 36, no. 4, pp. 149–172, 1987.
View at: Publisher Site | Google Scholar
T. Taga, “Analysis for mean effective gain of mobile antennas in land mobile radio environments,” IEEE Transactions on Vehicular Technology, vol. 39, no. 2, pp. 117–131, 1990.
View at: Publisher Site | Google Scholar
Y.-L. Ban, Y.-F. Qiang, Z. Chen, K. Kang, and J.-H. Guo, “A dual-loop antenna design for hepta-band WWAN/LTE metal-rimmed smartphone applications,” IEEE Transactions on Antennas and Propagation, vol. 63, no. 1, pp. 48–58, 2015.
View at: Google Scholar

Copyright

Copyright © 2021 Yan Wang and Zhengwei Du. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies