Long-Term Stability Studies and Applications of Ti<sub>3</sub>C<sub>2</sub>Tx MXene

Kumar, Sunil; Park, Hyun Min; Singh, Tej; Kumar, Manjeet; Seo, Yongho

doi:https://doi.org/10.1155/2023/5275439

International Journal of Energy Research

On this page

Abstract Introduction Methods Results and Discussion Conclusions Data Availability Conflicts of Interest Authors’ Contributions Acknowledgments Supplementary Materials References Copyright Related Articles

Research Article | Open Access

Volume 2023 | Article ID 5275439 | https://doi.org/10.1155/2023/5275439

Long-Term Stability Studies and Applications of Ti₃C₂Tx MXene

Sunil Kumar,¹Hyun Min Park,¹Tej Singh,²Manjeet Kumar,³and Yongho Seo¹

Academic Editor: Pawan Kumar Kulriya

Received06 Oct 2022

Revised10 Dec 2022

Accepted26 Dec 2022

Published03 Feb 2023

Abstract

The novel 2D materials, MXenes, have many remarkable properties, but their stability against oxidation is a major bottleneck in their applications. In this study, we have investigated the stability of Ti₃C₂T_x MXene for up to 365 days under different conditions, e.g., in liquid form in different solvents, in dried form when coated at polyethylene terephthalate (PET) substrate, and during the application of Ti₃C₂T_x MXene in polymer-dispersed liquid crystal- (PDLC-) based smart windows as conducting electrodes. In liquid form, the MXenes were dispersed in different solvents including an antioxidant in DI water and other organic solvents, and the corresponding color change was analyzed. To estimate the stability in dried form, the MXenes were coated on PET substrates and their relative sheet resistance change, i.e., , where is the initial resistance, was investigated under different conditions including MXene passivated with polymers and coated films stored under different environments. In the case of the MXene application-based stability study, the stability was investigated by using the MXenes as conducting electrodes in a switchable smart window application. The switchable behavior was observed by applying voltage (0-50 V) after different durations of up to 365 days. The MXene used in smart windows was preserved for a long time without additional treatment to MXene.

1. Introduction

Everlasting increasing demands in different industrial segments have provoked scientists all around the world to discover novel materials. Recently, there has been a focus on different kinds of nanomaterials, especially 2D materials like graphene, transition metal dichalcogenides (TMDs), and many other new materials. Among these materials, MXenes are among the most explored materials in the last decade. These materials have many remarkable properties like high hydrophilicity [1], high electrical conductivity [2], tunable band gap [3], surface area [4], and high electrochemical properties [5]. Due to these properties, these materials have found applications in energy storage, conductive ink, fuel cells, smart windows based on flexible transparent conducting electrodes (TCE), 3D printing, EMI shielding, supercapacitors, etc. [6–14]. These materials are obtained from the hexagonal carbides and/or nitrides with the general formula, M_n+1AX_n, popularly known as MAX phases, which are etched by the use of strong acids like HF or LiF/HCl [1]. In M_n+1AX_n, M is an early transition metal element, A is group 13 and 14 elements (mostly Al), X is C and/or N, and n is number from 1 to 4 [1]. After etching, the Al is removed and MXenes are subsequently washed with DI water thoroughly. MXenes have terminal groups, like -OH, -O, -Cl, or -F at their surface; hence, MXenes are generally represented as M_n+1X_nT_x, where T_x represents the terminal groups [2, 3]. Among various MXenes, Ti₃C₂T_x MXene has unique properties like excellent metallic conductivity, high EMI shielding, and ease of processing owing to its hydrophilic nature, etc. making Ti₃C₂T_x MXene the front runner in the MXene family [15]. Although Ti₃C₂T_x MXene has many unique properties [16–18], it is easily oxidized under ambient conditions. There are some reports indicating the highly oxidative nature of the Ti₃C₂T_x MXene.

To exploit the Ti₃C₂T_x MXene applicability, the stability against oxidation needs to be improved.

Earlier, some attempts have been made to improve the stability of MXene and stability also depends upon the synthesis process. The stability of MXenes can be improved when these are stored at low temperatures in an Ar environment [19] or stored in eutectic solvents [20], sodium L-ascorbate [21], etc. Another technique used for preservation is mixing these with polymers [22]. The oxidation of the MXene starts from the edges; hence, if these edges are capped with polyanions, the oxidation probability can be improved significantly [23]. The MXene preserved using antioxidants can also be used in energy storage applications even after 80 days under ambient conditions [24]. The passivation of MXenes by polymer is another method to maintain their stability against oxidation as the MXenes are preserved from being exposed to air; however, the electrical conductivity is reduced due to polymer passivation. In an earlier report, the poly(4-vinylphenol) (PVPh) was applied as a protective polymer layer on Ti₃C₂T_x MXene, and these electrodes were used in various flexible electronic devices [25]. However, after 25 days, the resistance of the polymer-coated MXene-based electrodes was found to increase up to 38%. The higher thickness of the polymer layer on Ti₃C₂T_x MXene has little impact on the stability of the MXene. The polymer passivated MXene was used in light-emitting displays, touch sensors, triboelectric nanogenerators, etc. Also, there are reports on the stability of MXene dispersed in different organic solvents; however, the observation time is limited [26]. In another report, the Al-Ti₃C₂ MAX phase was modified during synthesis to prepare the stable and most conductive Ti₃C₂ MXene till date, and the oxidation of MXene can be improved by controlling the defects [27]. The oxidation of MXene also depends upon the pH and temperature. At high pH and temperature, a high oxidation rate was observed. It was reported that under acidic conditions, the protonated hydroxyl terminal groups present at Ti₃C₂T_x flake surface, in the presence of water or oxygen, make Ti atoms prone to oxidative nucleophilic addition reaction which leads to the faster oxidation [28].

Besides, as another aspect, the stability of MXene has not been explored when these are used for some applications. Our group has reported earlier the fabrication of Ti₃C₂T_x MXene-based transparent conducting flexible electrodes in smart window fabrication [14], and the results encouraged us to analyze the stability studies without any special treatment for a duration of one year to estimate any commercial prospects in the future.

All these studies indicate the possibilities of Ti₃C₂ MXene phase oxidation and its prevention; however, the time frame is small. Still, there is a need to understand the oxidation conditions under one umbrella for a longer duration under which Ti₃C₂ MXene phase is oxidized so that preventative measures could be adopted accordingly.

In this report, we have presented 365 days study on MXene oxidation in a series of systematic studies in aqueous and dried environments after coating at PET substrate. In liquid form, the absorbance spectra and visual color change were studied, whereas, in the dried form, the stability of the Ti₃C₂ MXene phase was studied by calculating the relative resistance change () and transmittance change after regular intervals of time. Additionally, the stability of MXene was also studied during the application of MXene in polymer-dispersed liquid crystal- (PDLC-) based smart windows. These studies were made by observing the change in transmittance in on/off states at the 0-50 V voltage range.

2. Methods

The Ti₃C₂ phase MXene was synthesized from the Ti₃AlC₂ MAX phase (Carbon-Ukraine) as described in the supporting information (Section 1). The schematic structures of Ti₃AlC₂ MAX phase and Ti₃C₂ MXene phase are presented in Figure 1(f). The etched MXene was exfoliated by shaking and sonication techniques which were later centrifuged to get the exfoliated MXene. The exfoliated MXene was dispersed and stored in different solvents, e.g., DI water, acetone, isopropyl alcohol (IPA), ethanol, sodium L-ascorbate (SA), capping agent sodium dodecyl sulfate (SDS), f-CNTs (10%), and reduced graphene oxide (rGO, 10%) dispersions. In the dried form, the MXene was spin-coated on PET substrates and heated for 12 h at 100°C. The process of polymer passivation with NOA65 for MXene stability study has been discussed in supporting information (Section 2).

(a)

(b)

(c)

(d)

(e)

(f)

2.1. Characterizations

The morphology of Ti₃C₂ phase flakes and MXene film thickness were determined using a field emission scanning electron microscope (FESEM, SU8010 Hitachi, Japan) and AFM atomic force microscope (AFM, Nano focus Inc.). The elemental composition of MXene film was carried out using energy-dispersive X-ray spectroscopy (EDX). The crystalline phase of MXene was analyzed using an X-ray diffraction (XRD) system (PANalytical X’Pert Pro). The Raman microscopy (Renishaw, InVia, UK) was used to analyze the phonon modes of MXene. The transmittance of the substrate-coated MXene films’ electrooptical studies of the resultant smart windows was carried out using UV-Vis spectroscopy (Cary 5000, Varian, USA) with the help of a homemade AC voltage driver (0-50 V). The Brunauer-Emmett-Teller (BET) measurement (BELSORP-max, BEL Japan Inc.) was used to estimate the specific surface area of the MXene. The sheet resistance and electrical conductivity were estimated using a 4-point probe-based transport system (Ecopia, HMS-3000). The switching time (on/off time) of smart windows was recorded using a photodiode and laser diode assembly using an oscilloscope (Tektronix 1052B EDU, USA).

3. Results and Discussion

Prior to the stability studies, preliminary examinations of the Ti₃C₂T_x phase flakes, used in different stability studies, were carried out.

3.1. Morphological Studies

The size and thickness of synthesized MXene flakes under study were examined using FESEM and AFM analyses, and corresponding images are shown in Figures 1(a) and 1(b), respectively. The FESEM and AFM images indicate the MXene flakes of random size ranging from 100 nm to 1 μm. The thickness of the MXene flake is <2 nm as estimated from the AFM line profile shown in Figure 1(c).

3.2. Crystal Structure (X-Ray Diffraction) Analysis

The crystal structure of the Ti₃C₂ phase before and after etching was analyzed using XRD. The XRD patterns of the Ti₃AlC₂ MAX phase and Ti₃C₂ phase are shown in Figure 1(d). The XRD patterns for the Ti₃AlC₂ MAX phase and Ti₃C₂ phase accord well with the JCPDS card (JCPDS-52-0875 and JCPDS: 04-004-2919), respectively [29]. After etching, the (002) peak indicates a sharp shift towards a lower angle, i.e., from 2θ angle of 9.95° to 5.78° indicating the highly exfoliated MXene layers and the increase in the “c” lattice parameter [30, 31]. Additionally, the peak broadening suggests the reduced MXene layer thickness and increased d-spacing [21]. The spectrum indicates the disappearance of Al-associated (104) peak in the Ti₃C₂ phase [32].

3.3. Raman Analysis

The Raman spectra of the Ti₃AlC₂ MAX phase and Ti₃C₂ phase shown in Figure 1(e) were used to investigate the phonon-related vibrations and confirmation of terminal groups in MXene after etching. The Raman peaks were observed at around 200, 281, 365, 392, 565, 620, and 720 cm^-1 (indicated by purple dotted lines). These peaks confirm the formation of Ti₃C₂ having terminal groups with -F, -O, and -OH functionalities. These terminal groups can be collectively represented by T_x; hence, the Ti₃C₂ phase will be represented as Ti₃C₂T_x in the rest of the studies. These results accord well with those reported earlier [14, 33]. Additionally, the Raman spectrum of the Ti₃AlC₂ MAX phase exhibits peaks at around 250, 395, and 600 cm^-1 corresponding to E_2g, E_1g, and A_1g phonon vibrational modes (indicated by green dotted lines), which match with an earlier study [34].

3.4. Long-Term Stability Studies of Ti₃C₂T_x MXene

3.4.1. MXene Stability in Different Solvents

As the Ti₃C₂T_x is hydrophilic in nature, so the stability study was carried out in DI water also. The stability of MXene was studied for 365 days by dispersing the MXene in DI water at different concentrations, e.g., 1 mg/ml and 2 mg/ml. The real-time digital images of the samples are shown in Figure 2(a).

(a)

(b)

The images indicate the black color of the dispersed MXene in DI water on day 1. On day 30, there is no specific change in color. However, from day 60, there is a clear change in MXene color as the black-colored dispersion started appearing slightly milky color indicating the start of conversion of MXene to TiO₂ due to oxidation. However, the MXene with 2 mg/ml was found slightly darker than that at 1 mg/ml concentration, which is obvious as at low concentrations; MXene flakes are more exposed to DI water environment as evident from MXene at higher concentration (3 mg/ml) in DI water shown in Figure S1 (Supporting info.). On day 180, the color was completely turned to milky and slightly transparent in both cases. Till day 365, there is no significant change in the color as compared to day 180 as the Ti₃C₂T_x MXene is completely converted into the TiO₂. Under ambient conditions, there is a possibility of conversion of MXene into TiO₂ as predicted in the following reaction:

If the MXene has defects, then even the purest Ti₃C₂ can be oxidized to TiO₂ as

The major factor which leads to the oxidation is the atomic defects in Ti₃C₂T_x MXene. It has Ti-vacancies, which are probably associated with the Ti₃C₂T_x MXene during the process of chemical synthesis [35].

The degradation of MXene dispersed in DI water was also studied using absorbance spectroscopy, and the absorbance spectra recorded at different times are presented in Figure 3. The degree of oxidation of MXenes can be estimated from the decrease in the absorbance peak intensity at ~760 nm [36]. The spectra show the highest absorbance for MXene on day 1 as it has dark black color, and the intensity decreases with time. After day 60, the peak at around 750 nm on day 1 was observed to shift towards 780 nm, whereas after day 180, the peak almost disappeared indicating the degradation of MXene flakes possibly due to the formation of TiO₂ [27]. After 365 days, the MXene dispersion has negligible absorbance supporting the MXene conversion into white TiO₂ [37]. Also, Ti₃C₂T_x MXene can preserve its structural integrity up to before converting it into TiO₂ [38]. As per an earlier report, MXene flakes retain their structural integrity until the factor , which is the ratio of Ti atoms to O atoms in MXene flakes, reaching close to 3.5, i.e., ~1.75 oxygen atoms per Ti atoms; then there is a possibility that Ti₃C₂T_x MXene is converted into TiO₂. After day 60, the stability curve is exhibiting a mixed behavior of oxidized and nonoxidized MXene which indicates that some MXene flakes are oxidized or unstable and others are still stable as the intensity of the UV visible spectrum after day 60 was also found to be reduced as compared to that observed for fresh Ti₃C₂T_x MXene on day 1; simultaneously, the peak at 780 nm is not completely absent as in case TiO₂ on days 180 and 365. This trend can be predicted using where is the normalized absorbance, is the absorbance of stable MXene, is the absorbance of unstable MXene flakes at a particular wavelength, and is the time ()-dependent decay constant [36].

The stability of the MXene stored in different organic solvents, e.g., acetone, ethanol, and isopropyl alcohol (IPA), was also observed at the same MXene concentration (2 mg/ml). The real-time pictures of the MXene dispersed in these solvents are shown in Figure 2(b). There were no signs of oxidation as estimated from the color of MXene dispersions in organic solvents, and even after 365 days, the color of the MXene remained black. The MXene dispersions in these solvents were easily precipitated after a few seconds as MXene is not dispersible in these solvents. These results were similar as observed as reported earlier [26]; however, MXene dispersions are stable for even longer durations.

Another possible way to protect the oxidation of MXene is the use of antioxidants. The stability of the MXene (2 mg/ml) was studied using 5 mM, 10 mM, and 20 mM concentrations of antioxidant (SA) in DI water. It was found that at low SA concentration, the MXene was oxidized slowly as compared to DI water after 365 days whereas, at higher SA concentration, the color of MXene remains almost unchanged as indicated in Figure 4(a). It indicates that a small SA concentration (~10 mM) can preserve MXene for one year. Of course, higher SA concentration can also preserve Ti₃C₂T_x MXene for a longer duration but at the expense of the conductivity of the MXene because on day 1, as the MXene+SA mixture was spin-coated on PET film, the conductivity of MXene+SA-coated film in dried form is relatively lesser than that of MXene-only coated film (at same MXene concentration). It may be ascribed to the fact that SA is nonconducting, hence leading to an overall decrease in conductivity. However, for a longer duration, the SA preserves the MXene from being oxidized in solution form.

(a)

(b)

The stability of MXene was also studied with surfactant, sodium dodecyl sulfate (SDS, 0.1 M), 10% functionalized CNTs (f-CNTs), and reduced graphene oxide (rGO). All the dispersions include DI water and the images recorded on day 1 to 365 days are shown in Figure 4(b). It was observed that the MXene color was changed to turbid in SDS, whereas in rGO, the color changed to pale, indicating that MXene is oxidized in both media. The SDS is a popular capping agent for nanomaterials; however, it only partially prevented oxidation, probably because it failed to interact with the Ti₃C₂T_x surface [39]. A pale color in the MXene+rGO sample may be associated with the oxidation of rGO to GO [40]. However, in f-CNT, the black color of dispersion was maintained almost similar after 365 days.

3.4.2. MXene Stability Studies in Dried Form

In the above study, it was observed that the Ti₃C₂T_x MXenes are easily oxidized in DI water, indicating that DI water is a major factor in instigating the oxidation of the Ti₃C₂T_x MXene. To investigate the stability of Ti₃C₂T_x MXene in the dried form under ambient conditions, the Ti₃C₂T_x MXene films prepared by MXene dispersion in DI water were coated at PET substrates, and stability was estimated by measuring the relative resistance change. Additionally, the MXene dispersions prepared with different solvents were used to coat at PET film, and the sheet resistance was analyzed for 365 days under different conditions. The actual image of the MXene-coated PET film prepared from MXene dispersion in DI water is shown in Figure 5(a).

(a)

(b)

(c)

(d)

(e)

(f)

The film appears highly transparent as the background is clearly visible. The FESEM image showing the top surface view of the coated MXene film is shown in Figure 5(b), and the corresponding FESEM image with the cross-sectional view is shown in Figure 5(c). The thickness of MXene film appears around 10 nm which was also supported by AFM images and corresponding line profiles shown in Figures 5(d) and 5(e), respectively. The transparency of the coated MXene film was confirmed with the transmittance spectrum shown in Figure 5(f). The transmittance of film was found ~83% indicating high transparency which corroborates the visual image shown in Figure 5(a). The electrical parameters of MXene-coated PET film are presented in Table S1 (Supporting info.). The conductivity of the MXene film is much lower than the highest conductivity reported for Ti₃C₂T_x MXene (~20,000 S/cm) which may be associated with defects induced during the synthesis process [27].

(1) Surface and Electrical Study of MXene-Coated PET Films. The MXene dispersed in DI water was coated and analyzed for 365 days. The FESEM images of the MXene films under ambient conditions after 60, 180, and 365 days are shown in Figures 6(a)–6(c), respectively. It was observed that the edges of the MXene flakes have a boundary of powder-like material which is probably due to the oxidation of the MXene as the oxidation starts from the edges [23].

(a)

(b)

(c)

To analyze the oxidation, the elemental spectra were recorded and compared on day 1 spectrum with that on day 365 as shown in Figure S2(a) and Figure S2(b) (Supporting info.) and corresponding elemental composition as presented in Table S2 (Supporting info.). After day 365, the oxygen content increases more than double as compared to that of day 1. The oxidation of coated MXene film was also evidenced from transmittance spectra recorded on days 1, 30, 60, 180, and 365 as shown in Figure 7(a). It was found that over time, the transmittance slightly increases. The transmittance after day 30 is almost similar to day 1. After day 60, the transmittance difference is around 1-2%; however, after days 180 and 365, the transmittance increases by ~3% and ~5%, respectively. The increase in transmittance may be associated with the formation of more transparent TiO₂ particles. These results again justify the conversion of Ti₃C₂T_x MXene into TiO₂ particles [37].

(a)

(b)

(c)

(d)

Additionally, the stability was also observed by storing the coated MXene films, prepared by MXene dispersion in DI water, under different conditions like under a vacuum, MXene films in a petri dish covered with paraffin, NOA65 (1%) coating and UV curing, and MXene films stored under nitrogen (N₂) environment. The relative resistance change (), where is the difference between the final and initial resistance and is the initial resistance of MXene films stored under these conditions, is shown in Figure 7(b). MXene dispersions were spin-coated at PET substrates with subsequent drying at 100°C and corresponding was also analyzed. It was observed that MXene film under ambient conditions indicates a variation of ~3000%, whereas the MXene films stored under vacuum and coated with UV-cured NOA65 exhibited a small resistance change as compared to ambient conditions. MXene stability is improved with polymer passivation because it acts as a protective layer against ambient O₂ or moisture. The higher oxidation rate in MXene under ambient conditions may be ascribed to the presence of functional groups -O and other functional groups at the MXene surface which make these more reactive [36]. Similarly, the samples stored under the N₂ environment indicate low resistance change, whereas the MXene films in a petri dish wrapped with paraffin indicate moderate changes in resistance. All these storage experiments indicate that if the air or moisture is prevented, then the MXene can be preserved for a relatively long time. The of MXene dispersion in SDS (0.1 M) and SA (10 mM) coated on PET film were also studied under ambient conditions as shown in Figure 7(c). As expected, the SA-dispersed samples exhibited higher stability as compared to MXene only and MXene dispersed in SDS. Similarly, the of MXene, MXene+rGO, and MXene+f-CNT are shown in Figure 7(d). It was observed that relative resistance change for MXene+rGO-coated PET film is the highest among these three films, indicating that MXene+rGO-coated PET film oxidizes more rapidly than even MXene-only coated PET film. After 60 days, MXene+rGO-coated PET film became completely nonconducting (no measurable resistance); hence, plot was represented by the dotted line after 60 days. The MXene+f-CNT-coated film exhibited relatively better stability after 365 days as indicated by the lowest relative resistance change plot, which may be associated with the more stable CNTs.

3.4.3. MXene Stability during Application in Smart Windows

Many attempts are made to increase the stability of Ti₃C₂T_x MXene, but the final goal is to use the stabilized MXene in some applications. But with any additional treatment given to MXene, surely one must compromise on the conductivity of the MXene. But, if the MXene remains stabilized while being used in any application, then there is no need for additional treatment. The use of Ti₃C₂T_x MXene in polymer-dispersed liquid crystal- (PDLC-) based smart windows is one such application, in which the MXene while being used as a transparent conducting electrode, coated at transparent PET or glass substrates, is preserved from being exposed to air. We have seen in the above studies that MXene is oxidized rapidly under ambient conditions, but these are stabilized if protected by a polymer layer. During PDLC fabrication, the UV-curable polymer in the PDLC mixture is cured by the UV light which preserves the MXene from being exposed to air. The PDLC mixture was prepared by mixing NOA65 monomer with liquid crystals (1 : 1 wt.%) and sandwiched between MXene-coated PET transparent films. The prepared PDLC cell was cured under UV light for 10 minutes. The switching behavior (on/off) was studied at 0-50 V voltage range. The actual images of the MXene and PDLC-based smart window at the on state (50 V) and off state (0 V) are shown in Figure 8(a), and corresponding images after day 365 are presented in Figure 8(b). The off state is perfectly opaque as the background is not visible, and as the voltage is increased, the background becomes visible. The switching mechanism of the PDLC-based smart window is depicted in Figure S3 and discussed in section 6 in supporting information.

(a)

(b)

After 365 days, there seems to be no significant change in the PDLC cells, and these appear same as on day 1; however, the actual analysis was done using UV-visible spectra by plotting transmittance against voltage as presented in Figures 9(a) and 9(b).

(a)

(b)

On day 1, the off-state transmittance was ~4% (at ~580 nm), whereas the on-state transmittance is ~74%, maintaining a high contrast ratio (Figure 9(a)). These results are close to those with silver or ITO electrodes based on PDLC smart windows [41]. After 365 days, the on-state transmittance was ~70%, i.e., ~4% reduction than that on day 1, whereas the off-state transmittance remains almost unaltered (Figure 9(b)). Even at ~30 V, it maintains a >60% transmittance, which is closer to that on day 1 at the same voltage.

These results indicate that the PDLC smart window is still exhibiting high contrast ratio. It means that MXenes are conducting enough to generate a high electric field exhibiting good stability even after 365 days. It is because the MXene is preserved by the UV-cured NOA65 polymer, which is almost inert to air and moist atmosphere. The switching time, i.e., the on/off time, was also measured on days 1 and 365 as presented in Figure S4 (a-b) (Suppl. Info.). The plots indicate the switch on time on day 1 and millisecond. The switch off time has a slight lag in both cases which is an inherent feature of PDLC-based smart windows, and it is also observed in the case of indium tin oxide (ITO) or other electrode-based PDLC smart windows. Again, this also supports the stability of MXene in this application.

Hence, the use of Ti₃C₂T_x MXene in PDLC-based smart windows is one of the best ways to utilize MXene without giving additional treatment to the Ti₃C₂T_x MXene, and it could be a suitable alternative to costly and less flexible ITO.

4. Conclusions

In this study, we have performed a complete study on the long-term stability of Ti₃C₂T_x MXene under different conditions over a period of one year. The stability was studied in liquid form in different solvents including DI water. In the dried form, the stability of MXene film was studied under different storage conditions after being coated at transparent PET film. Additionally, stability was also studied during the use of Ti₃C₂T_x MXene-based transparent conducting electrodes in PDLC-based switchable smart windows. It was found that MXene is easily oxidized if exposed to DI water under ambient conditions, and after a certain time, it is converted into TiO₂ as the color of MXene dispersion was turned to white from dark black. In liquid form, the oxidation of MXenes can be controlled to some extent by using antioxidants. In dried form at PET substrate, the MXene oxidation rate is slow, and it can be further controlled by storing the MXene films under vacuum conditions or passivating with polymer as under these conditions MXene maintains high electrical conductivity even after 365 days. The oxidation can also be controlled to some extent by combining it with other materials, e.g., CNTs. The stability of MXene-coated PET films can be maintained for a long time if these are used as transparent conducting electrodes in PDLC-based smart windows, without any additional treatment to the MXene. MXene-based conducting electrodes maintain the switching behavior after 365 days in PDLC smart windows. MXene can be a suitable alternative to the more expensive and brittle ITO glass in smart window applications. This study not only investigates the stability of MXenes but also provides insight into the improvement of MXene stability under various conditions.

Data Availability

The data generated during the current study are available from the corresponding authors upon reasonable request.

Conflicts of Interest

There are no conflicts of interest to declare.

Authors’ Contributions

Sunil Kumar carried out experiments, data analysis, and manuscript writing. Hyun Min Park performed chemical etching and processing. Manjeet Kumar was responsible for electrical and transmittance studies. Tej Singh performed manuscript editing and grammar check. Yongho Seo contributed to funding, conceptualization, supervision, and manuscript writing.

Acknowledgments

This research was supported by a National Research Foundation of Korea (NRF) grant funded by the Korea government (MSIT) (NRF-2020R1A6A1A03043435 and 2020R1A2C1099862). Also, this research was supported by the Korea Institute for Advancement of Technology (KIAT) grant funded by the Korea Government (MOTIE) (P0012451, The Competency Development Program for Industry Specialist).

Supplementary Materials

This file provides the information about the MXene synthesis, MXene passivation by polymer, digital images of Ti₃C₂T_x MXene vials at 3 mg/ml concentration in DI water, electrical parameters of the MXene film, elemental composition of MXene, and polymer-dispersed liquid crystal-based smart window switching mechanism. (Supplementary Materials)

References

M. Naguib, V. N. Mochalin, M. W. Barsoum, and Y. Gogotsi, “25th anniversary article: MXenes: a new family of two-dimensional materials,” Advanced Materials, vol. 26, no. 7, pp. 992–1005, 2014.
View at: Publisher Site | Google Scholar
A. Lipatov, A. Goad, M. J. Loes et al., “High electrical conductivity and breakdown current density of individual monolayer Ti3C2Tx MXene flakes,” Matter-Us, vol. 4, no. 4, pp. 1413–1427, 2021.
View at: Publisher Site | Google Scholar
M. Khazaei, A. Ranjbar, M. Arai, T. Sasaki, and S. Yunoki, “Electronic properties and applications of MXenes: a theoretical review,” Journal of Materials Chemistry C, vol. 5, no. 10, pp. 2488–2503, 2017.
View at: Publisher Site | Google Scholar
Y. Dall'Agnese, M. R. Lukatskaya, K. M. Cook, P. L. Taberna, Y. Gogotsi, and P. Simon, “High capacitance of surface-modified 2D titanium carbide in acidic electrolyte,” Electrochemistry Communications, vol. 48, pp. 118–122, 2014.
View at: Publisher Site | Google Scholar
K. Maleski, C. E. Ren, M. Q. Zhao, B. Anasori, and Y. Gogotsi, “Size-dependent physical and electrochemical properties of two-dimensional MXene flakes,” ACS Applied Materials & Interfaces, vol. 10, no. 29, pp. 24491–24498, 2018.
View at: Publisher Site | Google Scholar
M. D. Levi, M. R. Lukatskaya, S. Sigalov et al., “Solving the capacitive paradox of 2D MXene using electrochemical quartz-crystal admittance and in situ electronic conductance measurements,” Advanced Energy Materials, vol. 5, no. 1, article 1400815, 2015.
View at: Publisher Site | Google Scholar
M. Ghidiu, M. R. Lukatskaya, M. Q. Zhao, Y. Gogotsi, and M. W. Barsoum, “Conductive two-dimensional titanium carbide 'clay' with high volumetric capacitance,” Nature, vol. 516, no. 7529, pp. 78–81, 2014.
View at: Publisher Site | Google Scholar
J. Li, X. T. Yuan, C. Lin et al., “Achieving high pseudocapacitance of 2D titanium carbide (MXene) by cation intercalation and surface modification,” Advanced Energy Materials, vol. 7, no. 15, article 1602725, 2017.
View at: Publisher Site | Google Scholar
W. Yang, J. Yang, J. J. Byun et al., “3D printing of freestanding MXene architectures for current-collector-free supercapacitors,” Advanced Materials, vol. 31, no. 37, article e1902725, 2019.
View at: Publisher Site | Google Scholar
C. J. Zhang, L. McKeon, M. P. Kremer et al., “Additive-free MXene inks and direct printing of micro-supercapacitors,” Nature Communications, vol. 10, no. 1, p. 1795, 2019.
View at: Publisher Site | Google Scholar
F. Shahzad, M. Alhabeb, C. B. Hatter et al., “Electromagnetic interference shielding with 2D transition metal carbides (MXenes),” Science, vol. 353, no. 6304, pp. 1137–1140, 2016.
View at: Publisher Site | Google Scholar
D. Liu, R. W. Wang, W. Chang et al., “Ti3C2 MXene as an excellent anode material for high-performance microbial fuel cells,” Journal of Materials Chemistry A, vol. 6, no. 42, pp. 20887–20895, 2018.
View at: Publisher Site | Google Scholar
S. J. Sun, C. Liao, A. M. Hafez, H. L. Zhu, and S. P. Wu, “Two-dimensional MXenes for energy storage,” Chemical Engineering Journal, vol. 338, pp. 27–45, 2018.
View at: Publisher Site | Google Scholar
S. Kumar, D. Kang, V. Nguyen et al., “Application of titanium-carbide MXene-based transparent conducting electrodes in flexible smart windows,” ACS Applied Materials & Interfaces, vol. 13, no. 34, pp. 40976–40985, 2021.
View at: Publisher Site | Google Scholar
Y. J. Wan, K. Rajavel, X. M. Li et al., “Electromagnetic interference shielding of Ti3C2Tx MXene modified by ionic liquid for high chemical stability and excellent mechanical strength,” Chemical Engineering Journal, vol. 408, article 127303, 2021.
View at: Publisher Site | Google Scholar
A. S. Zeraati, S. A. Mirkhani, P. C. Sun, M. Naguib, P. V. Braun, and U. Sundararaj, “Improved synthesis of Ti3C2Tx MXenes resulting in exceptional electrical conductivity, high synthesis yield, and enhanced capacitance,” Nanoscale, vol. 13, no. 6, pp. 3572–3580, 2021.
View at: Publisher Site | Google Scholar
M. Naguib, T. Saito, S. Lai et al., “Ti3C2Tx (MXene)-polyacrylamide nanocomposite films,” RSC Advances, vol. 6, no. 76, pp. 72069–72073, 2016.
View at: Publisher Site | Google Scholar
Y. Y. Liu, H. Xiao, and W. A. Goddard, “Schottky-barrier-free contacts with two-dimensional semiconductors by surface-engineered MXenes,” Journal of the American Chemical Society, vol. 138, no. 49, pp. 15853–15856, 2016.
View at: Publisher Site | Google Scholar
C. F. J. Zhang, S. Pinilla, N. McEyoy et al., “Oxidation stability of colloidal two-dimensional titanium carbides (MXenes),” Chemistry of Materials, vol. 29, no. 11, pp. 4848–4856, 2017.
View at: Publisher Site | Google Scholar
J. Kim, Y. Yoon, S. K. Kim et al., “Chemically stabilized and functionalized 2D-MXene with deep eutectic solvents as versatile dispersion medium,” Advanced Functional Materials, vol. 31, no. 13, p. 2008722, 2021.
View at: Publisher Site | Google Scholar
X. F. Zhao, A. Vashisth, E. Prehn et al., “Antioxidants unlock shelf-stable Ti3C2Tx (MXene) nanosheet dispersions,” Matter-Us, vol. 1, no. 2, pp. 513–526, 2019.
View at: Publisher Site | Google Scholar
T. Habib, X. F. Zhao, S. A. Shah et al., “Oxidation stability of Ti3C2Tx MXene nanosheets in solvents and composite films,” npj 2D Materials and Applications, vol. 3, p. 8, 2019.
View at: Google Scholar
V. Natu, J. L. Hart, M. Sokol, H. Chiang, M. L. Taheri, and M. W. Barsoum, “Edge capping of 2D-MXene sheets with polyanionic salts to mitigate oxidation in aqueous colloidal suspensions,” Angewandte Chemie. International Edition, vol. 58, no. 36, pp. 12655–12660, 2019.
View at: Publisher Site | Google Scholar
C. W. Wu, B. Unnikrishnan, I. W. P. Chen, S. G. Harroun, H. T. Chang, and C. C. Huang, “Excellent oxidation resistive MXene aqueous ink for micro-supercapacitor application,” Energy Storage Materials, vol. 25, pp. 563–571, 2020.
View at: Publisher Site | Google Scholar
S. Lee, E. H. Kim, S. Yu et al., “Polymer-laminated Ti3C2TX MXene electrodes for transparent and flexible field-driven electronics,” ACS Nano, vol. 15, no. 5, pp. 8940–8952, 2021.
View at: Publisher Site | Google Scholar
K. Maleski, V. N. Mochalin, and Y. Gogotsi, “Dispersions of two-dimensional titanium carbide MXene in organic solvents,” Chemistry of Materials, vol. 29, no. 4, pp. 1632–1640, 2017.
View at: Publisher Site | Google Scholar
T. S. Mathis, K. Maleski, A. Goad et al., “Modified MAX phase synthesis for environmentally stable and highly conductive Ti3C2 MXene,” ACS Nano, vol. 15, no. 4, pp. 6420–6429, 2021.
View at: Publisher Site | Google Scholar
S. Doo, A. Chae, D. Kim et al., “Mechanism and kinetics of oxidation reaction of aqueous Ti3C2Tx suspensions at different pHs and temperatures,” ACS Applied Materials & Interfaces, vol. 13, no. 19, pp. 22855–22865, 2021.
View at: Publisher Site | Google Scholar
H. B. Parse, I. Patil, B. Kakade, and A. Swami, “Cobalt nanoparticles encapsulated in N-doped carbon on the surface of MXene (Ti3C2) play a key role for electroreduction of oxygen,” Fuel, vol. 35, no. 21, pp. 17909–17918, 2021.
View at: Publisher Site | Google Scholar
Y. S. Peng, P. Cai, L. L. Yang et al., “Theoretical and experimental studies of Ti3C2 MXene for surface-enhanced Raman spectroscopy-based sensing,” ACS Omega, vol. 5, no. 41, pp. 26486–26496, 2020.
View at: Publisher Site | Google Scholar
R. Liu and W. H. Li, “High-thermal-stability and high-thermal-conductivity Ti3C2Tx MXene/poly(vinyl alcohol) (PVA) composites,” ACS Omega, vol. 3, no. 3, pp. 2609–2617, 2018.
View at: Publisher Site | Google Scholar
Y. Z. Li and X. T. Zhang, “Electrically conductive, optically responsive, and highly orientated Ti3C2Tx MXene aerogel fibers,” Advanced Functional Materials, vol. 32, 2022.
View at: Google Scholar
K. H. Lee, Y. Z. Zhang, Q. Jiang, H. Kim, A. A. Alkenawi, and H. N. Alshareef, “Ultrasound-driven two-dimensional Ti3C2Tx MXene hydrogel generator,” ACS Nano, vol. 14, no. 3, pp. 3199–3207, 2020.
View at: Publisher Site | Google Scholar
H. Ahmad, H. S. Albaqawi, N. Yusoff, L. Bayang, M. Z. B. Kadir, and C. W. Yi, “Tunable passively Q-switched erbium-doped fiber laser based on Ti₃C₂T_x MXene as saturable absorber,” Optical Fiber Technology, vol. 58, article 102287, 2020.
View at: Publisher Site | Google Scholar
F. J. Xia, J. C. Lao, R. H. Yu et al., “Ambient oxidation of Ti3C2 MXene initialized by atomic defects,” Nanoscale, vol. 11, no. 48, pp. 23330–23337, 2019.
View at: Publisher Site | Google Scholar
A. Iqbal, J. Hong, T. Y. Ko, and C. M. Koo, “Improving oxidation stability of 2D MXenes: synthesis, storage media, and conditions,” Nano Convergence, vol. 8, no. 1, 2021.
View at: Publisher Site | Google Scholar
J. X. Low, L. Y. Zhang, T. Tong, B. J. Shen, and J. G. Yu, “TiO₂/MXene Ti₃C₂ composite with excellent photocatalytic CO₂ reduction activity,” Journal of Catalysis, vol. 361, pp. 255–266, 2018.
View at: Publisher Site | Google Scholar
I. Persson, J. Halim, T. W. Hansen et al., “How much oxygen can a MXene surface take before it breaks?” Advanced Functional Materials, vol. 30, no. 47, article 1909005, 2020.
View at: Publisher Site | Google Scholar
J. B. Li, Q. Zhang, L. Yan et al., “Ultrafast flash energy conductance at MXene-surfactant Interface and its molecular origins,” Advanced Materials Interfaces, vol. 6, no. 23, article 1901461, 2019.
View at: Publisher Site | Google Scholar
R. T. M. Ahmad, S. H. Hong, T. Z. Shen, and J. K. Song, “Water-assisted stable dispersal of graphene oxide in non-dispersible solvents and skin formation on the GO dispersion,” Carbon, vol. 98, pp. 188–194, 2016.
View at: Publisher Site | Google Scholar
H. H. Khaligh, K. Liew, Y. N. Han, N. M. Abukhdeir, and I. A. Goldthorpe, “Silver nanowire transparent electrodes for liquid crystal-based smart windows,” Solar Energy Materials and Solar Cells, vol. 132, pp. 337–341, 2015.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2023 Sunil Kumar et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

International Journal of Energy Research

Long-Term Stability Studies and Applications of Ti3C2Tx MXene

Abstract

1. Introduction

2. Methods

2.1. Characterizations

3. Results and Discussion

3.1. Morphological Studies

3.2. Crystal Structure (X-Ray Diffraction) Analysis

3.3. Raman Analysis

3.4. Long-Term Stability Studies of Ti3C2Tx MXene

3.4.1. MXene Stability in Different Solvents

3.4.2. MXene Stability Studies in Dried Form

3.4.3. MXene Stability during Application in Smart Windows

4. Conclusions

Data Availability

Conflicts of Interest

Authors’ Contributions

Acknowledgments

Supplementary Materials

References

Copyright

Long-Term Stability Studies and Applications of Ti₃C₂Tx MXene

3.4. Long-Term Stability Studies of Ti₃C₂T_x MXene