Scrutinization of Slip Due to Lateral Velocity on the Dynamics of Engine Oil Conveying Cupric and Alumina Nanoparticles Subject to Coriolis Force

Arshad, Mubashar; Hussain, Azad; Hassan, Ali; Karamti, Hanen; Wróblewski, Piotr; Khan, Ilyas; Andualem, Mulugeta; Galal, Ahmed M.

doi:https://doi.org/10.1155/2022/2526951

Mathematical Problems in Engineering

On this page

Abstract Introduction Analysis of Results and Discussion Conclusions Data Availability Conflicts of Interest Acknowledgments References Copyright Related Articles

Research Article | Open Access

Volume 2022 | Article ID 2526951 | https://doi.org/10.1155/2022/2526951

Scrutinization of Slip Due to Lateral Velocity on the Dynamics of Engine Oil Conveying Cupric and Alumina Nanoparticles Subject to Coriolis Force

Mubashar Arshad,¹Azad Hussain,¹Ali Hassan,¹Hanen Karamti,²Piotr Wróblewski,^3,4Ilyas Khan,⁵Mulugeta Andualem,⁶and Ahmed M. Galal^7,8

Academic Editor: Ahmed Salem

Received29 Apr 2021

Revised20 Apr 2022

Accepted13 Aug 2022

Published20 Sept 2022

Abstract

This study is an attempt to investigate the three-dimensional flow of engine oil-based nanofluid under the impact of rotation and partial slip phenomenon over a stretchable surface. Partial slip condition is incorporated into the system at boundaries and the arising quotient of angular speed to stretching constant is regarded as rotation impression on freely moving three-dimensional flow of copper oxide-engine oil and aluminum oxide-engine oil nanofluid. The designed problem has been tackled numerically with the boundary value problem technique, this numerical mechanism requires one to transform the flow governing highly nonlinear PDEs into first-order differential equations along with associated boundary conditions. This procedure is carried out by employing a suitable similarity transformation. The investigation determines the impact of slip and rotation on primary and secondary velocity profiles, shear stress rates, and heat transfer coefficient. Minimum skin friction and Maximum Nusselt number has been observed for nanofluid under partial slip parameter as compared to nanofluid. Reduced skin coefficients were achieved for both nanofluids. Moreover, the outcomes of the study have been related with already available literature and were found in good agreement.

1. Introduction

Due to enhanced thermal performance, prospective advantages, and applications in different industries such as microelectronics, microfluidics, transportation, manufacturing, medical, and so on, several researchers are focused on the field of nanotechnology in recent years. Many research centers around the globe have established research facilities dedicated to the development of nanofluids. Crane [1] was the first who inspected the rotating flow over the stretching surface. This field of investigation was discovered to be quite fascinating and is currently being investigated under various physical limitations. Fang & Aziz [2] studied viscous flow owing to second-order slip velocity above a stretchable sheet. Hayat et al. [3] examined the 3D viscoelastic fluid flow above the stretching surface. Li et al. [4] have discussed the consequence of variable temperature transmission on Non-Newtonian fluid flow. Thakhar and Nath [5] elaborated on the unsteady rotating fluid flow above a stretchable sheet in the presence of a magnetic effect. Anantha et al. [6] discovered the magneto-hydrodynamic flow of micropolar fluid over a stretchable surface taking into account viscous dissipation with a improved heat flux model. Wang et al. [7] analyzed the viscous flow due to stretching sheets with suction and surface slip effect. Kumari and Nath [8] gave the analytical result of three-dimensional unsteady magneto-hydrodynamic boundary layer flow and heat transmission over a stretchable surface. Takhar and Nath [9] described the magnetic field impact for unsteady rotating fluid flow over an stretching sheet. Anderson et al. [10] described the heat transmission for the unsteady stretchable surface.

Choi presented the idea of enhancing the thermal conductivity of fluids by using nanoparticles. Patel et al. [11] experimentally explored the thermal conductivity improvement by using oxide nanoparticles in nanofluid. Such fluids proved to be more effective and efficient when compared to conventional fluids like water and ethylene glycol. Tawfik [12] gave an experimental review on applications and thermal conductivity improvement of nanofluids. Singh et al. [13] described the performance for carbon nanotubes-based fluids under the high temperature and high pressure. Lakshmisha et al. [14] deliberated heat and mass transmission for unsteady flow in three dimension above the continuously stretchable surface. Ali et al. [15] made finite element simulation for three-dimensional micropolar nanofluid flow with multislip effects.

The notion nanofluid was accessed by Choi and Eastman first time in the year 1995. They discovered a mechanism through which the temperature conductivity of a conventional fluid can be improved. This process involves the distribution of nanometer-sized particles into the host base fluid, this addition of nano-particle enhances the thermal transmission of the formed fluid termed “nanofluid.” Recently, a new phenomenon has been discovered, known as “Hybrid nanofluids.” These nanofluids are formed when more than one nano-meter sized nano-particle is distributed in the base fluid, as a result, an abrupt upsurge in thermal conductivity of the formed fluid occurs. Mahanta and Shaw [16] studied the Casson fluid flow with convective boundary conditions above the stretching surface. Bagherzadeh et al. [17] gave the competency of hybrid nanofluids. Hussain et al. [18] have carried out a computational investigation on three-dimensional rotating nanofluid flow with the mutual effect of nonlinear radiation and magnetic force. Arshad et al. [19] have described the impact of thermophoresis and Brownian diffusion on rotating nanofluids in the presence of chemical reactions and magnetization.

Hussain et al. [20] have introduced a comsolic model for compressible time-dependent fluid flow. Hassan et al. [21] have elaborated on different hybrid nanofluids over rotating cone for enhanced heat transfer coefficient with radiative and magnetic field effect. Hussain et al. [22] have examined heat transportation in hybrid nanofluids using carbon nanotubes over a rotating cone. Hassan et al. [23] have studied composite carbon nanotube and silver nanoparticles over the spinning body for a prescribed wall temperature case. Hussain et al. [24] investigated two distinctly positioned elliptic cylinders for heat transport enrichment. Many researchers worked on nanofluids under different effects and geometry [25–28]. Oudina [29] provided convective heat transmission of titania based nanofluid in an annulus cylinder with a distinct heat source. Abbas et al. [30] described the heat and mass transfer of nanofluid over a moving rotating plate incorporating nanoparticles shape factor. Swain et al. [31] illustrated the effect of hybrid nanoparticles on the non-linear porous shrinking surface with slip boundary and chemical reaction.

Many researchers [32–36] have made their investigations according to their area of interest using different geometries and effects. Haider et al. [37] examined the rotating cone fluid flow to assess the heat and mass transfer by numerical approach. Nasirzadehroshenin et al. [38] used CNT nanofluid in a tube for a better temperature transfer rate. Arshad et al. [39] gave an analysis for heat and mass transmission with chemical reaction above an infinite stretching surface. Wang et al. [40] gave DTM-Pade and LDM approximations above inclined permeable fin for convective and radiative temperature transmission.

The objective of the current study is the numerical investigation of the heat transmission possessions and velocity of rotating nanofluid over a stretchable surface in the incidence of a partial slip. In this study physical model, i.e., the single-phase nanofluid model is utilized to deliberate the problem. Through a deep literature review, no one has described the impact of rotation and partial slip on three-dimensional engine oil-based nanofluid with CuO and Al₂O₃ over the linear stretching surface in the presence of slip. Such flows are useful in a variety of applications in up-to-date devices, e.g., cooling of electronic chips, hot rollers, plasma flow, and geothermal engineering.

This motivates one to examine the effect of incorporating conditions of partial slip and rotation on these opted specific nanofluids. Thus, to study the influence of such parameters following research questions have been designed:(a)What is the result of increasing partial slip parameter on primary and secondary velocity profiles for both and nanofluids with fixed volume fraction of nanoparticles and rotation value(b)How the increment in slip parameter does effects the thermal boundary layer, skin coefficients, and heat transfer rates of and nanofluids(c)How does rotation affect the velocity and temperature constituents of and , and how does it affect important coefficients like skin friction and Nusselt number(d)Do the current outcomes provide a good agreement with already published previous results

2. Formulation of the Problem

Consider incompressible engine oil-based nanofluid is flowing over a flat stretchable sheet in the region which is rotating along the with fixed angular speed . Alongside the x-axis, two identical and opposite forces are applied such that the surface is stretched at a speed , strictly proportional to the distance from the origin at , The nanofluid is subjected to conditions of slip-flow. Figure 1 below, describes the flow configuration and coordinate system of the present problem.

2.1. Flow Governing Equations

The flow governing the three-dimensional flow of nanofluids above the surface is derived from classical Naiver-Stokes for incompressible viscous flow. The continuity, conservation of momentum, and energy equation along with boundaries are given as follows:

Here, is component, is component and is component of velocity , is fluid’s dynamic viscosity, is density, is the thermal diffusivity, T is the temperature, is the volumetric heat capacity of the nanofluid, is the volumetric heat capacity of the base fluid, is the volumetric heat capacity of the solid nanoparticles. All of these are related to the [27] particle volume fraction of nanoparticles as follows:

Here, is the thermal conductivity and density of the base fluid and solid nanoparticles, respectively. The corresponding boundary conditions are given as follows:

Here, is surface stretching velocity and is stretching rate. is surface slip parameter and is the kinematic viscosity.

2.2. Transformation Methodology

The following given similarity transformation is used to transform partial differential equations into ordinary differential equation to tackle numerically at Matlab.

Here, is the similarity parameter, and is the wall and free streams temperature, respectively.

Employing (8) in (1), the continuity will be uniformly satisfied and (4) will vanish. Equations (2)–(3) & (5) will transform into the following equations incorporating the thermo-physical relations (6) of nanofluid:

The boundary equations will take the following form:

In equations (9)–(11) is the rotation and denotes the Prandtl number, respectively and defined as follows:

Here, is the slip parameter. If then there is no slip.

2.3. Quantities of Engineering Importance

The skin frictions along the , , respectively, and heat transfer coefficient is known as Nusselt number are major quantities of physical and engineering importance. Here, and are shear stresses. These rate of heat flux and shear stresses are given as follows:

Here, and are shear stress and is heat flux. These quantities are defined as follows:

Now, the dimensionless form of these relations is obtained by utilizing the similarity transforms from equations (8) and (15) in equation (14). The dimensionless form of skin frictions and Nusselt from number is defined as follows:

Here, local Reynolds number is , Skin friction and heat flux are calculated for both nanofluid with the different significance of rotation constraint λ, and slip constraint

3. Numerical Scheme

A number of numerical techniques has been employed by numerous researchers to study different problems. In this present analysis, we have adopted the boundary value problem technique in Matlab. The highly nonlinear differential equations are first converted into first-order differential equations by defining the new set of variables. These first-order differential equations are tackled in Matlab. The assumed set of new variables is given as follows:

Now, the obtained first-order differential equations are as follows:

Similarly, the boundary conditions takes the form:

4. Analysis of Results and Discussion

The following two sections contain the analysis and discussion of obtained results for this study.

4.1. Analysis of Results

The accuracy of the present numerical results is supported by Tables 1 and 2. In the absence of slip and rotation, our results for skin friction and Nusselt number are in good accord with the literature.

4.2. Discussion of Results

This section discusses the influence of physical factors such as rotation and slip parameter K on temperature and velocity profiles for and -Engine oil nanofluids. Graphical data are obtained and analyzed in depth to estimate their true influence on velocity and temperature patterns. The figures are plotted for this purpose.

The influence of the slip parameter and the rotation on the velocity profile for both and -Engine oil nanofluid is depicted in Figures 2(a) and 2(b), respectively. By increasing the slip constraint a smooth rise in the boundary layer thickness for velocity profile but overall velocity decays for both and -Engine oil nanofluids is observed and seen in Figure 2(a). It is because, in the presence of slip, the velocity of the fluid nearby the sheet does not stay same to the surface stretching rate. As a result, raising the slip parameter increases slip velocity. It, therefore, slows the fluid’s velocity since the stretching surface is only partially drawn in this situation due to the presence of the slip factor. In addition, the slip parameter rises, while the thickness of the boundary layer decreases. However, it is interesting to note that the addition of nanoparticles causes a decrease in the velocity , whereas nanoparticles have the opposite effect (see Figure 2(a)). This is due to the fact that nanoparticles have a lower density as compared to nanoparticles. As a result, their inclusion in the base fluid results in less friction. As can be seen in Figure 2(b), increasing the rotation lowers the velocity profile , for both nanofluid. This occurs owing to the existence of slip velocity, which governs the fluid’s motion as its rotation increases. Furthermore, when compared to -Engine nanofluid, the wideness of the momentum boundary layer for -Engine nanofluid has been seen to grow sharply.

(a)

(b)

The effect of slip parameter and rotation on secondary velocity is accessible in Figures 3(a) and 3(b), respectively for both and -Engine oil nanofluids. In Figures 3(a) it is clear that the velocity declines when slip parameter rises near the wall. It is worth noting heat that as the partial slip increases the abrupt expansion in momentum boundary thickness was observed for the type of nanofluid. This further slows down the motion of a freely moving nanofluid. Figure 3(b) presents a decline in vertical velocity with a rise in rotation constraint . This particular behavior is eminent to be the same for both and -Engine oil nanofluids. The associated momentum boundary of both examined nanofluids dramatically takes a sudden cusp, and the wideness of the frontier layer has increased.

(a)

(b)

A distinction in temperature profile against the slip for and -Engine oil nanofluid is shown in Figure 4(a). It is fascinating to note that with an increment in slip the temperature profile drops dramatically. This shows that as the slip velocity of extending surface increases the temperature profile decreases as a result the associated temperature frontier layer for both explored nanofluids has contracted. It can be determined from Figure 4(a) that the temperature constituent considerably decays with an increase in slip constraint . The impact of rotation is observed on the temperature profile for both nanofluids in Figure 4(b). It was observed with increment in rotation parameter the temperature profile for both nanofluids has decreased abruptly. It is also worth noting that a severe contraction in the thermal boundary layer of free-moving nanofluid has been observed (See Figure 4(b)).

(a)

(b)

To check the distinctions on the skin friction constant and Nusselt number, the following tables are obtained. Table 3 characterizes the thermo physical characteristics of base liquid and nanoparticles. In Table 4, it can be demonstrated that for the fixed rotation parameter the skin friction decays and heat flux grows with a rise of for both nanoliquid. This is owing to the addition of solid nanoparticles in the host liquid. While nanoparticles have better temperature transmission compared to host liquid, so the temperature transference speed increases. Especially, conforming values of skin friction and heat flux are different for and which specifies the significance of types of nanoparticles. In addition, for fixed increasing slip decays the skin friction and. This is owing to a rise in slip clues to the reduction of friction and ultimately rises in temperature transmission at the wall. We observed that skin resistance of is always higher than , On the other side, is corroborated to be extra accomplished of fast conduction of temperature. Table 5 shows the effect of rotation on skin friction and heat transfer for both nanofluids. We discovered that amassed the rotation causes skin friction and heat transfer to rise. Both and - Engine oil nanofluid exhibit comparable characteristics. It is because a larger resistance at the surface arises from a higher spin for fixed slip .

Figures 5(a), 5(b), and 5(c) show the graphical representation of numerical outcomes. It is clear if Figure 5(a) that skin friction along increases by increasing the rotation parameter and higher skin friction is observed for . Figure 5(b) shows the influence of rotation on skin friction along the . The skin friction decays when rotation increases. It is worth noting behavior in Figure 5(c) that the Nusselt number increases as the rotation increases.

(a)

(b)

(c)

5. Conclusions

The impact of rotation and slip conditions is investigated on the rotating 3D flow of different nanofluids above a linearly stretching surface. The boundary value problem technique is employed in this study in Matlab and the convergence criterion of the problem is set up to 10⁻⁶. The influence of rotation and partial slip parameters are analyzed. The main outcomes of the study are as follows:(1)Velocity profiles increase for rise in slip and decrease for rise in rotation parameter(2)The effect of particle volume fraction on temperature profile is observed to be less evident in -Engine oil nanofluid and more prominent in -Engine oil nanofluid(3)For both nanofluids, increasing the velocity slip parameter K causes the increase in heat flow and skin friction to decrease(4)A lower rate of heat transfer and a greater rate of skin friction are both associated with a higher rate of rotational motion(5)Temperature profile increases rapidly in case of an increase in slip parameter while it increases slightly in case of a rise in rotation parameter(6)Compared to nanoparticles, nanoparticles were demonstrated to be superior heat transporters

Data Availability

All the data generated or analysed during this study are included in this published article.

Conflicts of Interest

The authors declare that there are no conflicts of interest.

Acknowledgments

This study was supported by the Princess Nourah bint Abdulrahman University Researchers Supporting Project number (PNURSP2022R192), Princess Nourah bint Abdulrahman University, Riyadh, Saudi Arabia.

References

L. J. Crane, “Flow past a stretching plate,” Zeitschrift für angewandte Mathematik und Physik ZAMP, vol. 21, no. 4, pp. 645–647, 1970.
View at: Publisher Site | Google Scholar
T. Fang and A. Aziz, “Viscous flow with second-order slip velocity over a stretching sheet,” Zeitschrift für Naturforschung A, vol. 65, no. 12, pp. 1087–1092, 2010.
View at: Publisher Site | Google Scholar
T. Hayat, M. Sajid, and I. Pop, “Three-dimensional flow over a stretching surface in a viscoelastic fluid,” Nonlinear Analysis: Real World Applications, vol. 9, no. 4, pp. 1811–1822, 2008.
View at: Publisher Site | Google Scholar
B. Li, L. Zheng, and X. Zhang, “Heat transfer in pseudo-plastic non-Newtonian fluids with variable thermal conductivity,” Energy Conversion and Management, vol. 52, no. 1, pp. 355–358, 2011.
View at: Publisher Site | Google Scholar
H. S. Takhar and G. Nath, “Unsteady flow over a stretching surface with a magnetic field in a rotating fluid,” Zeitschrift für Angewandte Mathematik und Physik, vol. 49, no. 6, pp. 989–1001, 1998.
View at: Publisher Site | Google Scholar
K. Anantha Kumar, V. Sugunamma, and N. Sandeep, “Influence of viscous dissipation on MHD flow of micropolar fluid over a slendering stretching surface with modified heat flux model,” Journal of Thermal Analysis and Calorimetry, vol. 139, no. 6, pp. 3661–3674, 2020.
View at: Publisher Site | Google Scholar
C. Y. Wang, “Analysis of viscous flow due to a stretching sheet with surface slip and suction,” Nonlinear Analysis: Real World Applications, vol. 10, no. 1, pp. 375–380, 2009.
View at: Publisher Site | Google Scholar
M. Kumari and G. Nath, “Analytical solution of unsteady three-dimensional MHD boundary layer flow and heat transfer due to impulsively stretched plane surface,” Communications in Nonlinear Science and Numerical Simulation, vol. 14, no. 8, pp. 3339–3350, 2009.
View at: Publisher Site | Google Scholar
H. S. Takhar and G. Nath, “Unsteady flow over a stretching surface with a magnetic field in a rotating fluid,” Zeitschrift für Angewandte Mathematik und Physik, vol. 49, no. 6, pp. 989–1001, 1998.
View at: Publisher Site | Google Scholar
H. I. Andersson, J. B. Aarseth, and B. S. Dandapat, “Heat transfer in a liquid film on an unsteady stretching surface,” International Journal of Heat and Mass Transfer, vol. 43, no. 1, pp. 69–74, 2000.
View at: Publisher Site | Google Scholar
H. E. Patel, T. Sundararajan, and S. K. Das, “An experimental investigation into the thermal conductivity enhancement in oxide and metallic nanofluids,” Journal of Nanoparticle Research, vol. 12, no. 3, pp. 1015–1031, 2010.
View at: Publisher Site | Google Scholar
M. M. Tawfik, “Experimental studies of nanofluid thermal conductivity enhancement and applications: a review,” Renewable and Sustainable Energy Reviews, vol. 75, pp. 1239–1253, 2017.
View at: Publisher Site | Google Scholar
T. Singh, I. W Almanassra, A. Ghani Olabi, T. Al-Ansari, G. McKay, and M. Ali Atieh, “Performance investigation of multiwall carbon nanotubes based water/oil nanofluids for high pressure and high temperature solar thermal technologies for sustainable energy systems,” Energy Conversion and Management, vol. 225, p. 113453, 2020.
View at: Publisher Site | Google Scholar
K. N. Lakshmisha, S. Venkateswaran, and G. Nath, “Three-dimensional unsteady flow with heat and mass transfer over a continuous stretching surface,” Pressure, vol. 23, p. 45423, 1988.
View at: Google Scholar
L. Ali, X. Liu, B. Ali, S. Mujeed, and S. Abdal, “Finite element simulation of multi-slip effects on unsteady MHD bioconvective micropolar nanofluid flow over a sheet with solutal and thermal convective boundary conditions,” Coatings, vol. 9, no. 12, p. 842, 2019.
View at: Publisher Site | Google Scholar
G. Mahanta and S. Shaw, “3D Casson fluid flow past a porous linearly stretching sheet with convective boundary condition,” Alexandria Engineering Journal, vol. 54, no. 3, pp. 653–659, 2015.
View at: Publisher Site | Google Scholar
S. A. Bagherzadeh, A. D’Orazio, A. Karimipour, M. Goodarzi, and Q. V. Bach, “A novel sensitivity analysis model of EANN for F-MWCNTs–Fe3O4/EG nanofluid thermal conductivity: o,” Physica A: Statistical Mechanics and its Applications, vol. 521, pp. 406–415, 2019.
View at: Publisher Site | Google Scholar
A. Hussain, M. A. Elkotb, M. Arshad et al., “Computational investigation of the combined impact of nonlinear radiation and magnetic field on three-dimensional rotational nanofluid flow across a stretchy surface,” Processes, vol. 9, no. 8, p. 1453, 2021.
View at: Publisher Site | Google Scholar
M. Arshad, A. Hussain, A. Hassan et al., “Thermophoresis and brownian effect for chemically reacting magneto-hydrodynamic nanofluid flow across an exponentially stretching sheet,” Energies, vol. 15, no. 1, p. 143, 2021.
View at: Publisher Site | Google Scholar
A. Hussain, A. Hassan, and M. Arshad, “Comsolic solution of an elliptic cylindrical compressible fluid flow,” Experience, vol. 64, p. 873, 2021.
View at: Google Scholar
A. Hassan, A. Hussain, M. Arshad et al., “Heat transport investigation of hybrid nanofluid (Ag-CuO) porous medium flow: under magnetic field and Rosseland radiation,” Ain Shams Engineering Journal, vol. 13, no. 5, p. 101667, 2022.
View at: Publisher Site | Google Scholar
A. Hussain, A. Hassan, Q. Al Mdallal et al., “Heat transport investigation of magneto-hydrodynamics (SWCNT-MWCNT) hybrid nanofluid under the thermal radiation regime,” Case Studies in Thermal Engineering, vol. 27, p. 101244, 2021.
View at: Publisher Site | Google Scholar
A. Hassan, A. Hussain, M. Arshad, M. M. Alanazi, and H. Y. Zahran, “Numerical and thermal investigation of magneto-hydrodynamic hybrid nanoparticles (swcnt-Ag) under rosseland radiation: a prescribed wall temperature case,” Nanomaterials, vol. 12, no. 6, p. 891, 2022.
View at: Publisher Site | Google Scholar
A. Hussain, A. Hassan, Q. Al Mdallal et al., “Heat transportation enrichment and elliptic cylindrical solution of time-dependent flow,” Case Studies in Thermal Engineering, vol. 27, p. 101248, 2021.
View at: Publisher Site | Google Scholar
A. Hussain, M. Arshad, A. Rehman et al., “Three-dimensional water-based magneto-hydrodynamic rotating nanofluid flow over a linear extending sheet and heat transport analysis: a numerical approach,” Energies, vol. 14, no. 16, p. 5133, 2021.
View at: Publisher Site | Google Scholar
A. Hussain, A. Hassan, M. Arshad, A. Rehman, R. T. Matoog, and T. Abdeljawad, “Numerical simulation and thermal enhancement of multi-based nanofluid over an embrittled cone,” Case Studies in Thermal Engineering, vol. 28, p. 101614, 2021.
View at: Publisher Site | Google Scholar
A. Hussain, M. Arshad, A. Hassan et al., “Heat transport investigation of engine oil based rotating nanomaterial liquid flow in the existence of partial slip effect,” Case Studies in Thermal Engineering, vol. 28, p. 101500, 2021.
View at: Publisher Site | Google Scholar
A. Hussain, M. Arshad, A. Rehman, A. Hassan, S. K. Elagan, and N. A. Alshehri, “Heat transmission of engine-oil-based rotating nanofluids flow with influence of partial slip condition: a computational model,” Energies, vol. 14, no. 13, p. 3859, 2021.
View at: Publisher Site | Google Scholar
F. Mebarek‐Oudina, “Convective heat transfer of Titania nanofluids of different base fluids in cylindrical annulus with discrete heat source,” Heat Transfer - Asian Research, vol. 48, no. 1, pp. 135–147, 2019.
View at: Publisher Site | Google Scholar
W. Abbas and M. M. Magdy, “Heat and mass transfer analysis of nanofluid flow based on, and over a moving rotating plate and impact of various nanoparticle shapes,” Mathematical Problems in Engineering, p. 242, 2020.
View at: Google Scholar
K. Swain, F. Mebarek-Oudina, and S. M. Abo-Dahab, “Influence of MWCNT/Fe 3 O 4 hybrid nanoparticles on an exponentially porous shrinking sheet with chemical reaction and slip boundary conditions,” Journal of Thermal Analysis and Calorimetry, vol. 147, no. 2, pp. 1561–1570, 2021.
View at: Publisher Site | Google Scholar
M. Ahmad, F. Ahmad, P. Wróblewski et al., “Prediction of ultimate bearing capacity of shallow foundations on cohesionless soils: a Gaussian process regression approach,” Applied Sciences, vol. 11, no. 21, p. 10317, 2021.
View at: Publisher Site | Google Scholar
M. Amjad, I. Ahmad, M. Ahmad, P. Wróblewski, P. Kamiński, and U. Amjad, “Prediction of pile bearing capacity using XGBoost algorithm: modeling and performance evaluation,” Applied Sciences, vol. 12, no. 4, p. 2126, 2022.
View at: Publisher Site | Google Scholar
M. Arshad, A. Hussain, A. Hassan et al., “Heat transfer analysis of nanostructured material flow over an exponentially stretching surface: a comparative study,” Nanomaterials, vol. 12, no. 7, p. 1204, 2022.
View at: Publisher Site | Google Scholar
P. Wróblewski and M. Niekurzak, “Assessment of the possibility of using various types of renewable energy sources installations in single-family buildings as part of saving final energy consumption in polish conditions,” Energies, vol. 15, no. 4, p. 1329, 2022, https://doi.org/10.3390/en15041329.
View at: Google Scholar
M. Arshad, A. Hussain, A. Hassan et al., “Thermal energy investigation of magneto-hydrodynamic nano-material liquid flow over a stretching sheet: comparison of single and composite particles,” Alexandria Engineering Journal, vol. 61, no. 12, pp. 10453–10462, 2022.
View at: Publisher Site | Google Scholar
Q. Haider, A. Hussain, A. Rehman, A. Ashour, and A. Althobaiti, “Mass and heat transport assessment and nanomaterial liquid flowing on a rotating cone: a numerical computing approach,” Nanomaterials, vol. 12, no. 10, p. 1700, 2022.
View at: Publisher Site | Google Scholar
F. Nasirzadehroshenin, M. Sadeghzadeh, A. Khadang et al., “Modeling of heat transfer performance of carbon nanotube nanofluid in a tube with fixed wall temperature by using ANN–GA,” The European Physical Journal Plus, vol. 135, no. 2, p. 217, 2020.
View at: Publisher Site | Google Scholar
M. Arshad, A. Hussain, A. Hassan et al., “Heat and mass transfer analysis above an unsteady infinite porous surface with chemical reaction,” Case Studies in Thermal Engineering, vol. 36, p. 102140, 2022.
View at: Publisher Site | Google Scholar
F. Wang, R. Varun Kumar, G. Sowmya et al., “LSM and DTM-Pade approximation for the combined impacts of convective and radiative heat transfer on an inclined porous longitudinal fin,” Case Studies in Thermal Engineering, vol. 35, p. 101846, 2022.
View at: Publisher Site | Google Scholar
C. Y. Wang, “Stretching a surface in a rotating fluid,” ZAMP Zeitschrift fr angewandte Mathematik und Physik, vol. 39, no. 2, pp. 177–185, 1988.
View at: Publisher Site | Google Scholar
R. Nazar, N. Amin, and I. Pop, “Unsteady boundary layer flow due to a stretching surface in a rotating fluid,” Mechanics Research Communications, vol. 31, no. 1, pp. 121–128, 2004.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2022 Mubashar Arshad et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies